background image

19

©   2 0 0 4   d i r e c t e d   e l e c t r o n i c s ,   i n c .

disarming

To disarm the security system, press 

. You will hear two

chirps, and the parking lights will flash twice. If the power locks

are controlled by the system, the doors will also unlock. The siren

chirping either four or five times when disarming indicates

Tamper Alert, which is described in the Diagnostics Section of

this guide.

The remote will indicate disarm notification with 2 beeps and 3

flashes of the Orange LED. If disarming after the system has been

triggered, the remote control will send a diagnostic notification as

a reminder. These diagnostic notifications are:

1. If a sensor triggered the system, the remote will beep 4-times

and the Orange and Red LEDs flash 3 times.

2. If a switch (Zone 1, 3, 5, or 6) triggered the system, the

remote will beep 4-times, the Orange LED will flash 6-times

and Red LED will illuminate for 3 seconds.

3. If the system was triggered so many times that NPC is active

the remote will emit the above notifications with 5 beeps

instead of 4.

high security disarm

This system includes High Security Disarm feature. If the system

is triggered this feature allows the user to silence the siren and

reset the system to the armed state without having to visually

checking the system status.

After receiving an alarm page:

Summary of Contents for Cyber 130XV





















































Reviews: