Directed Electronics 1090 Owner'S Manual Download | Manualshive

Page: 36 / 60

background image

© 2006 directed electronics—all rights reserved

b. The lights will flash as confirmation the remote start

command was received.

c. The system will send a remote start response to the remote

control.

d. A few seconds later the engine will start. For diesel vehicles

there may be a delay for the glow plugs to warm.

e. Once started, the engine will run for the programmed run

time and the lights will continue to flash or turn on.

“

remote

” The remote control Notification will be two beeps

ascending in tone followed by the remote start animation.

to drive the vehicle

a.  Disarm the alarm and unlock the doors
b.  Enter the vehicle but DO NOT step on the brake pedal.
c.  Insert the key and turn the ignition to the run or on posi-

tion

d. Step on the brake pedal, the remote start will shut down and

the engine will continue to run. You are ready to drive.

to turn the engine off

While the remote start is active, the system will turn off if any of
the following occur:

a. Press and release the

button of the remote control two

times quickly.

b. Step on the brake
c. Open the hood

«
...
34
35
36
37
38
...
»

Summary of Contents for 1090





























































Reviews:

No comments

Related manuals for 1090

Brand: Hama Pages: 75

HoneywellHome PROWLTOUCHWM

Brand: resideo Pages: 2

Brand: Conrad Pages: 64

Brand: TFA Pages: 2

Brand: TFA Pages: 30

Brand: Nexa Pages: 2

Brand: Ultra Start Pages: 4

Brand: ZETTLER Pages: 21

Brand: Uniden Pages: 8

Brand: ELOTEC Pages: 12

Brand: Prestige Pages: 16

Brand: Kele Pages: 2

Brand: Char-Broil Pages: 24

Brand: La Crosse Pages: 2

Brand: Orca Pages: 24

BW-1000 AVENGER

Brand: Black Widow Pages: 2

BW-1500 CHALLENGER PLUS

Brand: Black Widow Pages: 8

Brand: iHome Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands