Direct Supply ZERO OPENING ASSIST Owner'S Manual Download Page 5

5

1-800-634-7328    DirectSupply.com

4.   Set the pivot lock by inserting one or two set screws into the pivot lock holes in the back of the assist 

device mounting plate. See chart below for placement instructions:

To pivot to three positions:

To pivot to two positions:

To use as non-pivoting assist:

Insert one set screw into 

hole A (right hole with handle 

pointing up) using a 3 mm 

Allen (hex) wrench. Fully insert 

but do not tighten.

Insert one set screw into hole 

A and one set screw into 

either hole D or hole B (will 

prevent pivoting in the opposite 

direction of screw placement). 

Fully insert but do not tighten.

Insert one set screw into hole 

B and one set screw into hole 

D using a 3 mm Allen (hex) 

wrench. Fully insert but do 

not tighten.

 

* NOTE – hole placement on 

BACK of assist device

* NOTE – hole placement on 

BACK of assist device

* NOTE – hole placement on 

BACK of assist device

 

WARNING:

 

Do not allow the assist device to pivot in all four directions. Allowing the device to pivot 

toward the floor may potentially create a crush hazard and/or damage to your bed.

3.   Determine which direction(s) you want the 

assist device to pivot (up, right, left). 

or

D

+

 A

B

C

D

B

A

D

and

B

A

C

D

B

D

C

B

A

A

Summary of Contents for ZERO OPENING ASSIST













Reviews: