IR REMOTE CONTROL FOR
DAYLIGHT CONTROL SENSORS
CO REG R05
Supple:
1 battery x 3V CR2032 (included)
Battery lifetime:
4 years @ 100 puls/day
Infrared:
Focused and short-range transmission (max. 2 - 3m)
Compatible with:
RE DMS 001, RE DMS 003, RE DMS 004,
RE DMS DA1, RE DMS DA3 & RE DMS DA4
Environmental protection:
IP51
Working temperature:
0ºC ~ +45ºC
Dimensions:
105 x 50 x 12mm
TECHNICAL SPECIFICATIONS
INSTRUCTIONS MANUAL
OPERATION
This remote control allows programming of the Dayligh Control Systems,
without access to the ceiling, and more precisely, as well as manual
dimming.
There are 3 different operation modes:
· Programming Mode “Prog”: for setting the brightness target values (Day
and Night).
· Automatic Mode “Auto”: sets the operation mode on the Sensor (Auto or
Reg).
· Manual Mode: allows switching and dimming manually the light fixtures.
AUTOMATIC MODE
In this mode, the sensor’s LED will only light once it detects movement.
The lamps are automatically dimmed according to the brightness fixed level
and the daylight.
MANUAL MODE
In this mode, the sensor´s LED will keep constantly on.
Several keys are available for manual control: Dim up, Dim down, Swith on,
Switch off and Switch on at maximum.
When the remote control is unlocked, it does not indicate the mode in which
the sensor is. It is necessary to press the key of the mode that is wanted to
activate.
PROGRAMMING MODE
Night Setpoint setting:
Without daylight (at night or with the blinds lowered):
1º - Switch the lighting fixtures on with the remote control (ON key). The
red LED of the sensor will be switched on.
2º - Dim the luminaires to the necessary level to obtain the desired
brightness level. This level will be the maximum at which the
luminaires will be switched on.
3º - Wait for 30 seconds without hindering the light received by the sensor.
4º - Press the PROG key. Its LED will be switched on.
5º - Press the “ ” key pointing to the sensor. The luminaires will
The luminaires will flash 3 times indicating that the Night point has
been saved.
6º - Press the AUTO key pointing to the sensor.
Day Setpoint setting:
With enough natural light to reach the desired light level in the workplace:
1º - Switch the luminaires off by pressing the OFF key. The red LED on
the sensor will keep switched on..
2º - In case of insufficient natural light, turn the luminaires on with the
ON button and dim them to the required level to obtain the desired
brightness at the workplace.
3º - Wait for 30 seconds without hindering the light received by the sensor.
4º - Press the PROG key. Its LED will be switched on.
5º - Press the “ ” button pointing to the sensor. The luminaires will
will flash 3 times indicating that the Day point has been saved.
6º - Press the AUTO button pointing to the sensor.
NOTE:
The Sensor indicates that the set points (day and night) have been
stored by the triple flashing of the lamps after capturing the light value.
BATTERY REPLACEMENT
C/Auzolan 2, 20303 Irún (Spain)
Tel.: +34 943 627 988 / [email protected] / www.dinuy.com
KEY
FUNCTION
Lock
The remote control switches to "Lock" mode, and will
not respond to the next pressings. In this way, casual
pulsations are avoided and also contribute to the
battery saving.
Unlock
The remote control switches to "Unlock" mode, and
will respond to any press. If no key is pressed for
30sec, the remote control goes into Lock mode.
Manual Dimming
Keeping these keys pressed, the lighting is
dimmed manually.
Night setpoint
It saves the light level at night or without natural
light.
ON at Maximum
The luminaires are switched-on at its maximum level.
Automatic mode
Automatic mode is selected. The luminaires are
automatically dimmed depending on the desired light
level and the daylight.
Programming mode
Enters into programming mode to set the Day and
Night setpoints.
Day setpoint
It saves the light level with enough natural light.
Manual ON / OFF
The luminaires are permanently switched on or off
manually.
Reset
Allows to reset the factory settings (day and night
setpoints).
Battery LED
This light stays on while the keypad is unlocked and
constantly flashes to indicate that the battery is
running low.
YES
