Dini Argeo DGT100 User Manual Download Page 7

Page: 7 / 64

Optimized layout for A4 print.

USER_MAN_ENG_DGT100_V8

Dear Customer,

Thank you for purchasing a DINI ARGEO product.

This manual contains all the instructions for a correct installation and commissioning of the DGT100 4-channel digital weight indicator.

While thanking you for purchasing this product, we would like to draw your attention to some aspects of this manual.

This booklet provides useful information for the correct operation and maintenance of the scale to which it refers; it is therefore essential

to pay the greatest attention to all those paragraphs that illustrate the simplest and safest way to operate.

It is recommended that you carefully follow the instructions for programming the weight indicator; performing actions not indicated in this

manual could compromise the proper functioning of the scale.

The utmost care has been taken in compiling this manual, but reports of any inaccuracies are always welcome.

The instrument is covered by warranty and MUST NOT BE TAMPERED WITH BY THE USER under any circumstances.

Any attempt at repair or modification may expose the user to the danger of electric shock and voids any warranty conditions, relieving

the Manufacturer from all liability.

Any problem with the product must be reported to the manufacturer or to the retailer where it was purchased.

In any case, always TURN OFF THE POWER SUPPLY before any installation or repair operation.

Introduction

Summary of Contents for DGT100

































































Search results

Summary of Contents for DGT100

Reviews:

Brands by name

Popular brands

Dini Argeo DGT100, User Manual

Search results

Summary of Contents for DGT100

Reviews:

Brands by name

Popular brands