Dimplex WI 65TU, Installation And Operating Instruction

Page: 18 / 64

EN-2 452237.66.11 · FD 9908 www.gdts.one
English WI 65TU - WI 95TU
1 Please read
immediately
1.1 Important notes
ATTENTION!
!!
Work on the heat pump must only be performed by authorised and
qualified after-sales service technicians!
ATTENTION!
!!
When operating or maintaining a heat pump, the legal requirements of the
country where the heat pump is operated apply. Depending on the
refrigerant fill quantity, the heat pump must be inspected for leaks at
regular intervals by a certified technician, and these inspections must be
recorded.
ATTENTION!
!!
The well water must comply with the required water quality standards.
(see Cap. 9.4 on pag. 10)
ATTENTION!
!!
If the heat pump or circulating pumps are controlled externally, a flow rate
switch is required to prevent the compressor from being switched on
when there is no volume flow.
ATTENTION!
!!
The heat pump must not be tilted more than 45° (in any direction).
ATTENTION!
!!
Before commissioning, the transport fastening must be removed.
ATTENTION!
!!
Flush the heating system prior to connecting the heat pump.
ATTENTION!
!!
The maximum test pressure in the heating circuit and the primary circuit
is 6.0 bar. This value must not be exceeded.
ATTENTION!
!!
It is essential that the dirt trap included in the accessories pack is
installed in the return (inlet).
ATTENTION!
!!
The flow rate switch available as an accessory must be installed in the
flow (outlet) of the heat source.
ATTENTION!
!!
Ensure that there is a clockwise rotating field: With incorrect wiring the
starting of the heat pump is prevented. A corresponding warning is
indicated on the display of the heat pump manager (adjust wiring).
ATTENTION!
!!
It is not permitted to connect more than one electronically regulated
circulating pump via a relay output.
ATTENTION!
!!
Start-up must be performed in accordance with the installation and
operating instructions of the heat pump manager.
ATTENTION!
!!
The supplied dirt trap must be inserted in the heat source inlet of the heat
pump to protect the evaporator against the ingress of impurities.
ATTENTION!
!!
Disconnect all electrical circuits from the power source prior to opening
the device.
1.2 Intended use
This device is only intended for use as specified by the manufac-
turer. Any other use beyond that intended by the manufacturer is
prohibited. This requires the user to abide by the relevant project
planning documents. Please refrain from tampering with or alter-
ing the device.
1.3 Legal regulations and
directives
This heat pump is designed for use in a domestic environment
according to Article 1, Paragraph 2 k) of Eu directive 2006/42/EC
(machinery directive) and is thus subject to the requirements of
EU directive 2014/35/EC (low-voltage directive). It is thus also in-
tended for use by non-professionals for heating shops, offices
and other similar working environments, agricultural establish-
ments and hotels, guesthouses and other residential buildings.
This heat pump conforms to all relevant DIN/VDE regulations
and EU directives. Refer to the EC Declaration of Conformity in
the appendix for details.
The heat pump must be connected to the power supply in com-
pliance with all relevant VDE, EN and IEC standards. Any further
connection requirements stipulated by local utility companies
must also be observed.
The heat pump is to be connected to the heat source system and
the heating system in accordance with all applicable regulations.
This unit can be used by children aged 8 and over and by per-
sons with limited physical, sensory or mental aptitude or lack of
experience and/or knowledge, providing they are supervised or
have been instructed in the safe use of the unit and understand
the associated potential dangers.
Children must not play with the device. Cleaning and user main-
tenance must not be carried out by children without supervision
ATTENTION!
!!
Work on the heat pump must only be performed by authorised and
qualified after-sales service technicians!
ATTENTION!
!!
When operating or maintaining a heat pump, the legal requirements of the
country where the heat pump is operated apply. Depending on the
refrigerant fill quantity, the heat pump must be inspected for leaks at
regular intervals by a certified technician, and these inspections must be
recorded.
More information can be found in the accompanying log book.