background image

Models with Timer
DXLWP400TI, DXLWP800TI N & ARLWP800TI

Set the 

I

 - 

¡

¡

¡

¡

¡

 - 

O

 sli

de switch on the timer

(

Fig. 3

) to :

Position O - Heating Off

Position I - Manual operation

This setting allows power to the heater
uninterrupted by the timer settings. The
heat selector switch will control the output
(see ‘Using the heater’).

Position 

¡

¡

¡

¡

¡

 -  ‘Auto’ operation

DO NOT disconnect this heater from
the mains supply unless it is being
taken out of use (e.g. in summer or for
storage), otherwise the timer clock will
stop.

Setting the time of day

To set the time of day, rotate the timer
dial clockwise (indicated by the arrow)
until the correct time of day is opposite
the reference mark    (see 

Fig. 4

).

The 24-hour clock is used ; e.g. time shown for 3 pm is ‘15’
(15:00hrs).

Setting the ‘Auto’ ON and OFF times

To set the timer :

1.

 Using your finger tip or the tip of a

pencil, push in as many segments as
necessary around the dial, according
to the times you don’t require heat –
see Fig. 4. Each segment pushed in
switches the heater OFF for that part of
the hour. All other segments will be ON.
For example, Fig. 5 shows the timer
set to switch the heater ON between 7
am and  9 am and between 4 pm and
9.30 pm .

2. 

 You can select as many ON periods

as you like, within the 24-hour day. The

settings will repeat every day until changed.

3.

 To change ON and OFF times, simply push in any ‘ON’

segments you wish to cancel and pull out new ‘ON’ segments
as required.

Switching to auto

Set the heat selector and thermostat for the heat output required.
Check that the 

clock shows the correct time of day. Set the

 

I - 

¡

¡

¡

¡

¡

- O

 

slide switch to 

 

¡

¡

¡

¡

¡

 (see Fig. 4)  - the convector will  switch ON

and OFF according to the timer settings (see Fig 5).

IMPORTANT NOTES

Remember to observe all safety warnings when operating the
heater on auto setting unattended or attended .
If the mains supply to the heater is interrupted, th

e timer clock

will stop until power is restored ; reset the time of day to ensure
correct ON and OFF times.

Fig. 3

11

15

13

12

14

O

I

Fig. 4

Fig. 5

11

O

12

13

15

I

14

Summary of Contents for ARLWP800TI

Page 1: ...ntroller timer or any other device which switches the heater on automatically observe all safety warnings at all times 600 mm 400W 800 mm 800W 500 mm Important Safety Advice WARNING THIS APPLIANCE MUST NOT BE USED IN A BATHROOM WARNING DONOTUSETHISHEATERINTHEIMMEDIATE SURROUNDINGSOFABATH ASHOWERORASWIMMING POOL WARNING THIS HEATER MUST NOT BE LOCATED IMMEDIATELYBELOWAFIXEDSOCKETOUTLET The plug mus...

Page 2: ...on key supplied 3 Place feet over base of heater align holes and engage hook on foot into the recess on the back of the heater see Fig 1 4 Replace the screws but do not overtighten Fig 1 Rear View 3 Drill the wall at the three marked positions and fit the wall plugs Ensure template has been removed 4 Fix two No 8 screws to the top two holes leaving 3mm of the screw exposed Hang the heater on the s...

Page 3: ...mes you don t require heat see Fig 4 Each segment pushed in switches the heater OFF for that part of the hour All other segments will be ON For example Fig 5 shows the timer set to switch the heater ON between 7 am and 9 am and between 4 pm and 9 30 pm 2 You can select as many ON periods as you like within the 24 hour day The settings will repeat every day until changed 3 To change ON and OFF time...

Page 4: ...ire after sales service you should contact our customer services help desk on 0870 727 0101 It would assist us if you can quote the model number series date of purchase and nature of the fault at the time of your call The customer services help desk will also be able to advise you should you need to purchase any spares Please do not return a faulty product to us in the first instance as this may r...

Reviews: