background image

2002 Dimension One Spas Export Owner’s Manual 

 

 

      Note

 

When pouring antifreeze into the rear-most bleeder valve fitting, you may see antifreeze pouring 
from one or both of the circulation system return fittings. 

 

 

    Danger 

DO NOT USE AUTOMOTIVE COOLING SYSTEM ANTIFREEZE IN YOUR SYSTEM. IT IS 
TOXIC AND HARMFUL TO HUMANS AND ANIMALS. CHECK WITH YOUR LOCAL SPA 
DEALER OR RV DEALER TO PURCHASE NON_TOXIC ANTIFREEZE THAT IS COMPATIBLE 
WITH DRINKING WATER SYSTEMS! 
 

 

20.  Replace all equipment access panels onto the system. 

 

21.  Replace thermal cover and secure locking tabs. If your system is located in an area of high snowfall, you 

may want to take one more extra precaution to safeguard the life of your system cover. Span the cover 
with (2 or more) 2x4’s cut to length to reach the outside edges of your cover. Place a sheet of plywood, 
cut to fit each half of the cover, over the 2x4’s; this will carry the load of a heavy snow load and prevent 
the cover from warping or breaking. You can even tarp the system at this point for maximum protection. 

Spring Time Startup 

In the spring, or when your ready to start the system back up, follow these instructions. 
 

• 

Make sure o-rings for pumps are in place and undamaged. 

• 

Make sure all the fittings that you had to loosen are tightened. 

• 

Replace all jet fittings, pump drain plugs, hose bib drains and bleeder valves 

• 

Fill the system up, as you would normally do. 

• 

Turn the power back on. 

• 

Run the jets on high speed for about 15 minutes. 

• 

Drain the water. 

• 

Put your filter(s) back in. 

• 

Refill and treat chemically like you would during a normal water change. 

 

 

  Caution 

Your system is equipped with automatic freeze protection. However, power outages can cause 
your system equipment to freeze quickly. During freezing conditions, check your system frequently 
to ensure proper operation. Always check your system after any power failure to ensure that it is 
operational. Draining and not operating your system disables this feature.  

 

For additional information about winterizing your spa, please contact your local Authorized Dimension One Spas 
dealer. 

 

 

28

Summary of Contents for 2002 Arena









































Reviews: