DIGITIZE DET-16 User Manual Download Page 9

Page: 9 / 55

Introduction

Digitize Inc.

700271-0001 Rev. G 05/13

DET-16 Controller Bd. in Enclosure

1.2

Specifications

AC Power In

115 VAC 50/60 Hz @ 250 mA Max.

EOL Inputs

16 Supervised 4.7k Ohm End of Line Resistor Inputs

Telegraph Relay Outputs

1 Form C (SPDT) contacts rated for 6 Amps max. @ 24 VDC or
120 VAC.

Alarm Output Contacts

1 Form C (SPDT) contacts rated for 6 Amps max. @ 24 VDC or
120 VAC.

Trouble Output Contacts

1 Form C (SPDT) contacts rated for 6 Amps max. @ 24 VDC or
120 VAC.

Display

4 line x 20 character, 5 x 7 dots with yellow LED backlight.
Viewing Area: 76 mm Wide x 25.2 mm High.

Keypad

4 x4 Conductive Rubber Switchpad

LED Indicators

Alarm (Red), Trouble (Yellow), Loop Problem (Yellow),
Watchdog (Red), AC/DC Input (Green)

Beeper

2,200 ± 300 hz. @ 85 dB.

Ethernet

10/100BASE-T Ethernet – Auto-Sensing

USB

USB version 2.0

Standby Battery

7.5 Amp Hour Sealed Lead Acid, Digitize PN 900414-0004

Panel Size

13.5” wide x 15” high x 4“ deep

Construction

Electro Galvanized Steel chassis, plastic front bezel

System Weight

approx. 18 lbs. including 7.5 amp hour battery.

Summary of Contents for DET-16
























































Search results

Summary of Contents for DET-16

Reviews:

Related manuals for DET-16

Brands by name

Popular brands

DIGITIZE DET-16, User Manual

Search results

Summary of Contents for DET-16

Reviews:

Related manuals for DET-16

Brands by name

Popular brands