DIGITIZE DET-16 User Manual Download Page 42 | Manualshive

Page: 42 / 55

background image

Det-16 Programming Utility

Digitize Inc

36

700271-0001 Rev. G 05/13

6.3

Operation

The Det-16 Programming Utility allows perform the following tasks on a Det-16 panel:

•

Upload firmware to the Det-16

•

Download the firmware currently installed on the Det-16.

•

Download the settings from the Det-16 panel.

•

Edit the settings for the Det-16 panel.

•

Save the settings to disk.

•

Load settings from disk.

•

Upload settings into the Det-16.

6.3.1

The File Menu

The File Menu pull down tab allows you to Open and Save Det-16 configurations. Selecting
“New” configuration loads all of the default settings for a Det-16 into the programmer
software.

6.3.2

The Transfer Menu

The Transfer Menu contains all the routines for uploading and downloading the firmware
and the configurations for the Det-16.

«
...
40
41
42
43
44
...
»

Summary of Contents for DET-16
























































Reviews:

No comments

Related manuals for DET-16

Brand: Icom Pages: 4

Brand: Magnetrol Pages: 16

Brand: R.L.DRAKE Pages: 46

Brand: Ranger Communications Pages: 11

MAGNETIC Deluxe 1Rw

Brand: YOODA Pages: 2

Brand: Yaesu Pages: 34

NEO-FiberLink-2

Brand: G&D Pages: 32

FM Transmitter 2

Brand: C. Crane Pages: 13

Brand: RF Limited Pages: 4

Brand: Questtel Pages: 15

exta life RNK-22

Brand: Zamel Pages: 8

Long Range Transmitter 2

Brand: Gatekeeper Systems Pages: 5

Brand: Zaxcom Pages: 37

DpharpEJX vigilantplant EJX510A

Brand: YOKOGAWA Pages: 49

Brand: Icom Pages: 2

Brand: Accsoon Pages: 49

Brand: Kubu, inc. Pages: 6

Brand: Icom Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands