manualshive.com logo in svg

DigiTech RP-20 VALVE, User Manual

Share
Download
DigiTech RP-20 VALVE User Manual Download Page 39

Noise Gate 

The Silencer noise reduction system is definitely going to become your best friend in any recording session or live performance for keeping
signals quiet.  

Noise Gate Parameters

Type

Selects the type and placement of the noise reduction to be used. 

Threshold

Set the minimum input level at which the compressor will engage. Ranges from -90 to 0.

Attenuation

Adjusts how far the signal is lowered when the gate is closed. Ranges from 1 to 5.

Attack

Controls how quickly the gate opens after the signal level reaches Thresh. Range: 1 to 10.

Release

Determines how quickly the the gate closes after the signal falls below the Threshold. Ranges from: 1 to 10.

Compressor

Compressor Parameters

Level

Controls the signal input level fed to the module. Ranges from Off to 100%.

Threshold

Sets the threshold level of the compressor. Ranges from -27 to 0.

Ratio

This parameter sets the compressor ratio. Ranges from 1.5 to 40.

Gain

This parameter controls the amount of gain in the compressor. Ranges from 0 to 200%.

Attack

This parameter controls the attack time of the compressor. Settings are: Slo, Med and Fast.

Release

This parameter sets the release of the compressor. Settings are: Slo, Med and Fast.

Delay

This parameter sets the delay time of the compressor. Ranges from 0 to 10 ms.

RP-20 Valve

User Guide

Section - 4 Editing Modules 

31

Summary of Contents for RP-20 VALVE












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands