DigiTech JamMan Solo Owner'S Manual Download

Page: 40 / 52

The JamMan

Solo offers 35 minutes of

total built-in loop memory storage. You

can increase the loop memory by installing

an optional SD/SDHC memory card into

the SD card slot found under JamMan

Solo’s

PEDAL SWITCh

. The JamMan

Solo is compatible with SD/SDHC card

sizes up to 32GB for over 16 hours of total

loop memory.

The first time a memory card is inserted

into the JamMan Solo, it is recommended

that you format the card using the JamMan

Solo’s format procedure (see page 38 for

formatting instructions).

To install an optional SD/SDHC memory

card into the JamMan Solo, follow these

steps:

Disconnect the power supply.

Depress either of the two

PEDAL

SWITCh RELEASE PINS

fully using

the 1/4” plug on a guitar cable.

Lift and remove the

PEDAL SWITCh

from the JamMan Solo chassis.

Insert the memory card into the card

slot contacts face down and press until

it seats solidly. To remove the memory

card, press on the edge to activate the

spring mechanism that pops the card out

slightly and then gently pull the card out.

Replace the

PEDAL SWITCh

by placing one hole of the

PEDAL

SWITCh

over its corresponding pin.

Push the opposite pin in and lower the

other side of the

PEDAL SWITCh

into place over the depressed pin.

Release the pin. When the

PEDAL

SWITCh

is properly fastened, both

release pins are flush with the outer side.

Using Optional SD/SDhC Memory Cards

Summary of Contents for JamMan Solo





















































Search results

Summary of Contents for JamMan Solo

Reviews:

Related manuals for JamMan Solo

Brands by name

Popular brands

DigiTech JamMan Solo, Owner'S Manual

Search results

Summary of Contents for JamMan Solo

Reviews:

Related manuals for JamMan Solo

Brands by name

Popular brands