DIGITAL DELAY ELITE 500 Manual Download Page 21 | Manualshive

Page: 21 / 21

DIGITAL DELAY ELITE 500 Manual Download Page 21

21

Mounting the Elite 500

For complete viewing of the large LCD, care should be taken when mounting the unit to make sure that the display is angled

towards the driver’s eyes. Before mounting the Elite 500, place the box in the desired location and check the legibility of the display
in both day and night conditions. As shown below, the lower the box is placed below eye level, the more the angle amount needs to
increase for viewing.

Wiring the Elite 500

Driver

Dash

Box

Driver

Dash

Box

+12 Volts

Trans

S.F.O.

T-Stop

Shift

Ground

P.B. 1

P.B. 2

Tap Up

Tap Down

L.L.P.B.

Connect to Ground

Connect to Ground

Connect to Ground

Connect to Ground

Connect to +12

Symbol for Push-button

Connect to a Chassis Ground, Not

Connect to a +12 to 16 Volt source capable of driving 40

Connect to Transbrake Solenoid and 2-Step if used

Connect to any device to be controlled by the S.F.O.

Connect to a Throttle Stop

Connect to the Shifter

Symbol for 15 Amp fuse

«
...
19
20
21

Summary of Contents for ELITE 500






















Reviews:

No comments