11
Pro Mode Screens
To enter into Pro Mode, while displaying any of the first five bracket screens, press and release the Set Up key and then
press and release the number nine key. This will turn on the Pro Mode and display the Pro Screen. This is the only way to enable the
Pro Mode features of the Elite 500. When Pro Mode is turned on the Bracket Mode settings are turned off with the exception of the
S.F.O. and the P.T.S.O. settings. However all Bracket Mode settings are retained in memory and will be available when the Elite 500
returns to Bracket Mode. The Pro Mode of the Elite 500 has 5 different screens. While in Pro Mode, the Set Up key is used to move
from screen to screen. When viewing a Pro Screen there will be a set of arrows on the right side of the LCD. These selection arrows
point to the selected line on the screen. There will only be one selected line on the screen at a time, with the exception of lines 1 and
2 on Screen 4. To change the selected line, press and release the Next key. The selection arrows will move to the next line on the
screen. If the line selected is at the bottom of the screen the selection arrows will return to the top of the screen when the Next key is
pressed and released again. Once a line has been selected the setting or value for that line can be changed.
Each of the Pro Screens display four lines of information, these are shown below.
Screen
Number and Type
Line 1
Line 2
Line 3
Line 4
1)
Pro
Shift
Point
Stage
1
Stage
2
Delay
2) Set Up
Stage 1 - Timer 1
Stage 2 - Timer 1
Stage 3 - Timer 1
Stage 4 – Timer 1
3) Set Up *
Stage 1 - Timer 2
Stage 2 - Timer 2
Stage 3 - Timer 2
Stage 4 – Timer 2
4) Set Up **
Shift Point
Shift Number
Multi-Shift
Shift Mode
5) Driver’s Reaction Tester
Reaction Time
Average
Fastest
Slowest
* Will only be displayed if S.F.O. is set to mode 2
** Will only display if Multi-Shift is greater than 1.
Pro Mode Settings for Screen 1
When the Elite 500 is displaying Screen 1 the Pro Screen, The Shift Point for the first shift is displayed on line 1, Stage 1 of
Pro Timer 1 is displayed on line 2, Stage 2 of Pro Timer 1 is displayed on line 3, and the Delay is displayed on line 4. Only the first
Shift Point can be displayed on line 1 the rest of the Shift Points are shown on Screen 4. The first two stage times shown on the Pro
Screen are the same as the first two stage times shown on Screen 2.
Setting the First Shift Point
When the Pro Screen is first displayed the selection arrows will be on line 3 (Stage 2), this means that line 3 is selected. To
change the Shift Point, line 1 must first be selected. Use the Next key to move the selection arrows to line 1. Once the first line has
been selected press and release the Clear key, line 1 will now be blank indicating the unit is ready to accept the Shift Point. Now
using numerical keys enter the new time, leading zeros do not have to be entered. For example if 0.800 for a Shift Point time is
desired 800 would be entered on the keypad. If less than four digits are entered for a time, pressing the Next key will act as an enter
key and the leading zeros will displayed on the LCD. As the numbers are entered they are shown on the display, indicating the
numbers are accepted and entered into memory. If a mistake is made while entering the Shift Point, press and release the Clear key
and reenter the Shift Point again.
The Scrolling Arrow keys can also be used to change the Shift Point. First make sure that the selection arrows are on line 1.
If not, use the Next key to move the selection arrows to line 1. Once line 1 has been selected pressing and releasing the Up Arrow
key will cause the Shift Point to increase by one. While pressing and releasing the Down Arrow key will cause the Shift Point to
decrease by one. If the Up Arrow key is held down the Shift point will scroll up and if the Down Arrow key is held down the Shift
Point will scroll down.