Dietz Sango Advanced F User Manual Download Page 18 | Manualshive

Page: 18 / 44

Dietz Sango Advanced F User Manual Download Page 18

5.8. Armrest settings

Armrest width (also affects seat width)

1. Loosen the allen screw (A) by two turns

(figure 19).

2. Slide the armrest (B) to the side.

3. If required, remove or position the

spacer ring (C).

4. Slide the armrest back.

5. Tighten the allen screw.

Armrest height

1.

Loosen the bolt (A + B figure 20).

2. Slide the armrest (C) into the desired

position.

3. Tighten the bolt.

4. If required, adjust the armrest pad

angle (figure 22).

Warning

Ensure that the arms are well supported,

without the shoulders being pushed

upwards.

Armrest pad width and depth

1.

Loosen the two allen screws (A figure

21).

2. Slide the bolts with the armrest pad (B)

into the other guide bar (C) to adjust

the armrest pad width.

3. Adjust the armrest pad depth to the

desired position.

4. Tighten the allen screws.

C

B

A

3

2

1

3

B

2

A

C

1

21

3

1

C

B

2

A

B

19

20

5 Wheelchair settings (qualified specialists only)

18 - SANGO ADVANCED / SLIMLINE

«
...
16
17
18
19
20
...
»

Summary of Contents for Sango Advanced F













































Reviews:

No comments