Dickey-John Instalab 700 NIR, Operator'S Manual

Page: 23 / 111

OPERATOR’S MANUAL
Instalab 700 NIR Product Analyzer
11001-1574-201107
CALIBRATIONS 19
Figure 9
Calibration File Example
[Main] ;Revised 26 Apr 2011 (MB etc) rws
PL=DDGS ;The Product Label to be used by the instrument
F0=2310 ;Filter #0 wavelength in nm / 0 if not required
F1=0
;Filter #1 wavelength in nm / 0 if not required
F2=2180 ;Filter #2 wavelength in nm / 0 if not required
F3=2100 ;Filter #3 wavelength in nm / 0 if not required
F4=1940 ;Filter #4 wavelength in nm / 0 if not required
F5=1680 ;Filter #5 wavelength in nm / 0 if not required
F6=0
;Filter #6 wavelength in nm / 0 if not required
F7=0 ;Filter #7 wavelength in nm / 0 if not required
F8=1759 ;Filter #8 wavelength in nm / 0 if not required
F9=2340 ;Filter #9 wavelength in nm / 0 if not required
SM=ON
;Sample Motor (SM) is ON or OFF during measurement
Gain=S ;S for standard / E for enhanced
[C0] ;Start of Constituent 0
CL=Crude Protein ;Constituent Label
UL=30
;Upper Limit
LL=25 ;Lower Limit
Units=% ;w/w (Indicate here with a note ratio units: w/w = wt/wt or v/w = vol/wt)
MB=A ;Native Calibration MB
;(Blank) if moisture
;A = As-Is
;0 - Dry Basis
;XX.X for XX.X Basis where XX.X is %Moisture value
AMB=15.0 ;Alternative MB
;XX.X Moisture value
;A = As-Is
;Leave blank if not required
;if [MC_Basis=N] AND [(MB=0 or XX.X)AND (AMB=0 or xx.x) OR ((MB=A or AMB=A) AND MC_Basis=Y Exists in file)]
MC_Basis=N ;Moisture Constituent for Basis (N - No / Y - Yes)
Display=NA
;N=Native Calibration only
;NA=Native calibration and Alternate MB
;A=Alternate MB only
;(blank)=Do not display this constituent
Format=00.0 ;Display Format (00.0 / 00.00 / 00.000)
Adj_Bias=0 ;Adjustable Bias Default Value=0.0 Range +/- 100
Adj_Slope=1.00
;Adjustable Slope Range = .80 to 1.20 %x=Adj_Slope (Bias+K0*L0 ;+K1*L1+ … ) + Adj_Bias
;Default Value = 1.00
KA=23.28346 ;Default Bias
K0=-0.21294 ;K0
K1=0
;K1
K2=0.74628 ;K2
K3=-0.51264 ;K3
K4=0
;K4
K5=-.08296 ;K5
K6=0
;K6
K7=0 ;K7
K8=0 ;K8
K9=0.07167 ;K9
[C1] ;Start of Constituent 1 (add constituents in this pattern up to 10 total)
CL=Moisture ;Constituent Label
UL=14 ;Upper Limit
LL=7 ;Lower Limit
Units=% ;w/w (Indicate here with a note ratio units: w/w = wt/wt or v/w = vol/wt)
MB= ;Native Calibration MB
;(Blank) if moisture
;A = As-Is
;0 - Dry Basis
;XX.X for XX.X Basis where XX.X is %Moisture value
AMB= ;Alternative MB
;XX.X Moisture value
;A = As-Is
;Leave blank if not required
;if [MC_Basis=N] AND [(MB=0 or XX.X)AND (AMB=0 or xx.x) OR ((MB=A or AMB=A) AND MC_Basis=Y Exists in file)]
MC_Basis=Y ;Moisture Constituent for Basis (N - No / Y - Yes)
Display=N
;N=Native Calibration only
;NA=Native calibration and Alternate MB
;A=Alternate MB only
;(blank)=Do not display this constituent
Format=00.0 ;Display Format (00.0 / 00.00 / 00.000)
Adj_Bias=0 ;Adjustable Bias Default Value=0.0
Adj_Slope=1.00 ;Adjustable Slope %=Adj_Slope (Bias+K0*L0 ;+K1*L1+ … ) ;+Adj_Bias
;Default Value = 1.00
KA=12.43708 ;Default Bias
K0=.24596 ;K0
K1=0
;K1
K2=0 ;K2
K3=0 ;K3
K4=.09395 ;K4
K5=.15049 ;K5
K6=0
;K6
K7=0 ;K7
K8=-.11842 ;K8
K9=-.34051 ;K9
[Main]
ISS=201006291715 ;Based on date & time; any change modifies (YYYYMMDDTTTT)
CS=0
;Encrypted check-sum
;Set to "0" for Open file