background image

FEATURES

Technical

• Fully Regulated Power Supply
• Up To 5V RMS Input Signal Voltage Capability
• High pass x-over 12 dB/oct. fixed at 80 Hz (front, rear, and center only)
• Low pass x-over 12 dB/oct. 60 Hz-250 Hz (sub channels only)
• Sub-sonic filter 12 dB/oct. 17 Hz-80 Hz (sub channels only)
• Independant Gain for Each Set of Channels, Including Center
• Gain Bypass (sub channels only)
• 2 oz. Copper Circuit Board
• Massive Proprietary Heatsink
• Individual Channel Protection Circuitry

Convenience/Appearance

• Fully Variable Electronic Crossovers
• Nickel Plated Solid Brass, Circuit Board Mounted, 4 Gauge Direct

Power/Ground Connector Blocks

• Nickel Plated Solid Brass, Circuit Board Mounted, 10 Gauge Direct or

Banana Plug Direct Speaker Connectors

• Billet Aluminum End Plates
• Fully Adjustable Mounting Feet

SPECIFICATIONS

Frequency Response:

10 – 50,000 Hz

Signal-to-Noise Ratio:

100dB

THD Front, Rear, and Center:

0.03%

THD Sub Channels:

0.05%

Channel Separation:

80dB (min.)

Input Sensitivity:

.2 to 5V RMS

Input Impedance:

>20k Ohms

Power Supply Operating Range:

11 to 14.5V DC

1   Diamond Audio Technology

Summary of Contents for D5 5.1

















Reviews: