background image

Page 1 

icon Audio 

 

Instruction Manual Covering: 

 

Stereo 40i Classic 

EL34 versions 

 

KT88 Version pictured 

Contents 

 

1 Introduction & Final Inspection 

 

2 Quick Set Up Guide 

 

3 Connecting inputs & outputs 

 

4 Getting the best out of your 

amplifier 

 

5 Trouble Shooting 

 

6 Specifications 

 

7 Valve Replacement  

 

8 Guarantee 

 

9 Packing Instructions 

 

1 Introduction 

 

Thank you for purchasing the 

Stereo 40i 

Classic

. This new upgraded model benefits 

from a Choke regulated power supply for an even 
smoother sound plus several other circuit 
improvements. 
In order to get the best out of your amplifier, 
please read the enclosed notes. Even if you are 
experienced with hi fi. 

We would recommend 

that everyone follow the ‘quick set up guide’. 

Should you be uncertain about anything to do with 
your amplifier please contact your dealer, or 
ourselves for advice. 
Hi fi reproduction is a long chain of events that 
includes the recording, editing, mixing etc, before 
being transferred to a medium such as LP, CD, or 
FM, before being played through your own source 
unit, the amplifier and finally loudspeakers.  
Your room acoustics will also affect the sound 
before it finally reaches your ear. Whilst the 
amplifier is arguably the most important part of a 
system, it is important to remember that the 
weakest link will always affect the final results 
when making judgements. And not all recordings 
are ‘equal’! Therefore an amplifier which faithfully 

reproduces the input signal will also reproduce 
imperfections in the tonal balance and the 
recording itself. So setting up and judgements 
should be made with a ‘clean’ well balanced 
recording. Time should also be allowed for the 
amplifier to “burn in”, this applies not only to the 
valves but also capacitors and resistors etc. We 
are aware this can be several months depending 
upon your pattern of use. Generally the sound will 
become more relaxed and cohesive. 
The 

Stereo 40i 

is a push-pull Ultralinear 

stereo power amp, capable of running in either 
“ultralinear” or pure triode mode, using the EL34 
valves in fixed bias mode. The driver and phase 
splitting is all triode. The pre-amp is a high quality 
‘Passive’ circuit using silver audio cable and an 
ALPS ‘blue’ volume control. It is sensitive enough 
to be used with all modern source equipment 
having an output of 300mv or greater. Its 
simplicity coupled with “point to point wiring” “hard 
wiring without” the use of printed circuit boards 
results in an open euphoric sound that is 
wonderfully detailed and warm sounding.  
 

Summary of Contents for Stereo 40i Classic EL34









Reviews: