background image

HIGHPASS ON/OFF

Pushing this button “IN” engages the Highpass filter. Pushing this button
“OUT” will bypass the filter.  There is one of these switches for each of the
front, rear and center channels.

SLAVE SELECT

It is possible to completely run your 

D5 5.1

off of only one set or input RCA’s.

The rear, center, and sub channels can all be slaved of the front channels
inputs.  Simply push the appropriate button “IN” to slave that channel to those
inputs.  You can also slave just the center and sub channels if you have a four
channel input.

SUBSONIC ON/OFF

Pushing this button “IN” engages the sub-sonic filter on the sub channels.
Pushing this button “OUT” will bypass the filter.

SUBSONIC FREQUENCY

Turning this control sets the sub-sonic filter point from 17 Hz (fully
counterclockwise) to 80 Hz (fully clockwise).

LOWPASS ON/OFF

Pushing this button “IN” engages the lowpass filter on the sub channels.
Pushing this button “OUT” will bypass the filter.

LOWPASS FREQUENCY

Turning this control sets the lowpass crossover point from 60 Hz (fully
counterclockwise) to 250 Hz (fully clockwise).

SUB CHANNEL INVERSION SELECT

Pushing this button “IN” inverts the phase of the sub channels by 180 degrees.
Pushing this button “OUT” keeps the sub channels in phase.

CROSSOVER FREQUENCY DIAGRAMS

Sub-sonic

Lowpass

250 Hz

60 Hz

155 Hz

79 Hz

98 Hz

117 Hz

136 Hz

174 Hz

193 Hz

212 Hz

231 Hz

11:00

10:00

9:00

8:00

12:00

1:00

2:00

3:00

4:00

80 Hz

17 Hz

48.5 Hz

23.3 Hz

29.6 Hz

35.9 Hz

42.2 Hz

54.8 Hz

61.1 Hz

67.4 Hz

73.7 Hz

11:00

10:00

9:00

8:00

12:00

1:00

2:00

3:00

4:00

9   Diamond Audio Technology

Summary of Contents for D5 5.1

















Reviews: