DFI KU171 User Manual Download

Page: 20 / 65

www.dfi .com

Chapter 2 Hardware Installation

Chapter 2

SATA (Serial ATA) Connectors

• 2 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s

• Integrated Advanced Host Controller Interface (AHCI) controller

• Supports

RAID

0/1/5

The Serial ATA connectors are used to connect Serial ATA devices. Connect one end of the Se-

rial ATA data cable to a SATA connector and the other end to your Serial ATA device.

BIOS Setting

Configure the Serial ATA drives in the Advanced menu (“SATA Configuration” submenu) of the

BIOS. Refer to chapter 3 for more information.

Features

SATA 3.0 6Gb/s

SATA (Serial ATA) Power Connectors

These SATA power connectors supply power to the SATA drive. Connect one end of the pro-

vided power cable to the SATA power connector and the other end to your storage device.

+12V

Ground

SATA 0

RXN GND

TXP

TXN

GND

RXP

GND

SATA 1

SATA

Power 0

SATA

Power 1

Summary of Contents for KU171


































































Search results

Summary of Contents for KU171

Reviews:

Related manuals for KU171

Brands by name

Popular brands

DFI KU171, User Manual

Search results

Summary of Contents for KU171

Reviews:

Related manuals for KU171

Brands by name

Popular brands