DFI KU171 User Manual Download

Page: 31 / 65

www.d

.com

Chapter 3 BIOS Setup

Chapter 3

ACPI Configuration

This section is used to configure the system ACPI parameters.

Determines the action tak-
en when the system power
is off and a PCI Power
Management Enable wake
up event occurs.

ACPI Confi guration

Wake On LAN <Enabled>

After G3 <Always On>
Wake On RTC <Disabled>

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

Wake On LAN

This field is used to enable or disable the LAN signal to wake up the system.

After G3

This field is to specify what state to go when power is re-applied after a power failure

(G3 state).

Always On

The system working state.

Always Off

Off, except for trickle current to devices such as the power button.

Wake On RTC

Automatically power the system on at a particular time every day from the Real-time

clock battery.

Wake up time

When Wake On RTC is set to enabled, specify the wake up time of the day: <hour>

(00~23), <minute> (00~59), <second> (00~59).

Note:

Under Dual Boot Type or UEFI Boot Type mode, if Quiet Boot is set to enabled,

BGRT Logo field will appear for configuration. Refer to the Boot menu (page

) for

more information.

Support display logo with
ACPI BGRT table.

ACPI Confi guration

Wake On LAN

After G3 <Always On>

BGRT Logo <Enabled>

Wake On RTC <Disabled>

Advanced

Help

↑

↓

Select Item

F5/F6

Change Values

Setup Defaults

Esc

Exit

←

→



Select Item

Enter

Select



SubMenu

F10

Save and Exit

InsydeH2O Setup Utility

Rev. 5.0

BGRT Logo

This field is used to enable or disable to support display logo with ACPI BGRT table.

Summary of Contents for KU171


































































Search results

Summary of Contents for KU171

Reviews:

Related manuals for KU171

Brands by name

Popular brands

DFI KU171, User Manual

Search results

Summary of Contents for KU171

Reviews:

Related manuals for KU171

Brands by name

Popular brands