DFI G5G330-P User Manual Download Page 57 | Manualshive

Page: 57 / 117

background image

57

2

Hardware Installation

DIMM Standby Power LED

This LED will turn red when the system’s power is on or when it is
in the Suspend state (Power On Suspend or Suspend to RAM). It
will not light when the system is in the Soft-Off state.

PCI Standby Power LED

This LED will turn red when the system is in the power-on, Soft-Off
or Suspend (Power On Suspend or Suspend to RAM) state.

Important:

If the DIMM Standby Power LED or PCI Standby Power LED is
lighted, you must power-off the system then turn off the power
supply’s switch or unplug the power cord prior to installing any
memory modules or add-in cards.

DIMM and PCI Standby Power LEDs

DIMM Standby

Power LED

PCI Standby

Power LED

«
...
55
56
57
58
59
...
»

Summary of Contents for G5G330-P






















































































































Reviews:

No comments

Related manuals for G5G330-P

Brand: Acrosser Technology Pages: 7

Brand: Aaeon Pages: 65

Brand: Embest Pages: 91

DS-5116HFI Series

Brand: HIKVISION Pages: 22

Brand: Tadao Pages: 3

Brand: Intel Pages: 74

Brand: Humandata Pages: 8

MT9M031I12STCH-GEVB

Brand: ON Semiconductor Pages: 5

GA-N650SLI-DS4L

Brand: Gigabyte Pages: 100

Brand: Supermicro Pages: 1

TAS5001-5122C2EVM

Brand: Texas Instruments Pages: 27

Brand: DataExpert Pages: 44

Brand: AGP Pages: 65

Brand: Teridian Pages: 32

Brand: SOYO Pages: 30

Brand: Asus Pages: 22

Brand: Asus Pages: 22

Brand: Asus Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands