DFI G5G330-P User Manual Download Page 59 | Manualshive

Page: 59 / 117

background image

59

2

Hardware Installation

The system board is equipped with one PCI Express x16 and one
PCI Express x1 slots.

PCI Express x16

Install PCI Express x16 graphics card, that comply to the PCI
Express specifications, into the PCI Express x16 slot. To install a
graphics card into the x16 slot, align the graphics card above the
slot then press it down firmly until it is completely seated in the slot.
The retaining clip will automatically hold the graphics card in place.

PCI Express x1

Install PCI Express x1 card such as network cards or other cards
that comply to the PCI Express specifications into the PCI Express
x1 slot.

PCI Express x16 and x1 Slots

PCI Express x16

PCI Express x1

«
...
57
58
59
60
61
...
»

Summary of Contents for G5G330-P






















































































































Reviews:

No comments

Related manuals for G5G330-P

Brand: Yanmar Pages: 44

Brand: DFI Pages: 39

Brand: AOpen Pages: 8

Brand: NXP Semiconductors Pages: 14

Brand: MSI Pages: 112

K8N Neo3 MS-7135

Brand: MSI Pages: 124

Brand: ASROCK Pages: 64

A320M PRO-VH PLUS

Brand: MSI Pages: 154

Brand: PRIZM Pages: 9

STEVAL-PLC001V1

Brand: ST Pages: 42

Brand: National Semiconductor Pages: 22

Brand: Atmel Pages: 39

Brand: Gigabyte Pages: 37

Brand: Vox Pages: 93

Brand: Gigabyte Pages: 44

TLV320AIC12KEVM-K

Brand: Texas Instruments Pages: 40

Brand: Supero Pages: 121

Brand: Gigabyte Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands