DFI G5G330-P User Manual Download Page 92

Page: 92 / 117

9 2

BIOS Setup

Resources Controlled By

The Award Plug and Play BIOS has the capability to automatically
configure all of the boot and Plug and Play compatible devices.

Auto

The system will automatically detect the settings for you.

Manual

Choose the specific IRQ in the “IRQ Resources” field
respectively.

IRQ Resources

Move the cursor to this field and press <Enter>. This field is used to
set each system interrupt to either Reserved or PCI Device.

PCI/VGA Palette Snoop

This field determines whether the MPEG ISA/VESA VGA cards can
work with PCI/VGA or not. The default value is Disabled.

Enabled

MPEG ISA/VESA VGA cards work with PCI/VGA.

Disabled

MPEG ISA/VESA VGA cards does not work with PCI/
VGA.

Maximum Payload Size

This field is used to select the maximum TLP payload size of the PCI
Express devices. The unit is byte.

The settings on the screen are for reference only. Your version may not be identical
to this one.

Summary of Contents for G5G330-P






















































































































Search results

Summary of Contents for G5G330-P

Reviews:

Related manuals for G5G330-P

Brands by name

Popular brands

DFI G5G330-P, User Manual

Search results

Summary of Contents for G5G330-P

Reviews:

Related manuals for G5G330-P

Brands by name

Popular brands