DFI BT700 User Manual Download Page 31

Page: 31 / 52

www.dfi .com

Chapter 3 BIOS Setup

Chapter 3

PCI Express Confi guration

PCI Express Port 0

Speed

PCI Express Port 1
Speed

PCI Express Port 2
Speed

PCI Express Port 3
Speed



[Enabled]

[Auto]

[Enabled]
[Auto]

Chipset



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

PCI Express Configuration

This section configues settings relevant to PCI Express devices.

Enable or Disable the
PCI Express Port 0 in the
Chipset

PCI Express Port 0-3

Enable or disable the PCI Express port in the chipset.

Speed

Select the speed for the PCI Express devices. The options are Auto, Gen1 or Gen2.

Audio Confi guration

Audio Controller

Azalia HDMI Codec

DP/HDMI Port B



[Enabled]

[Enabled]
[Enabled]

Chipset



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

Azalia HD Audio

This section configues Azalia HD Audio options.

Control Detection of the
Azalia device. Disabled =
Azalia will be uncondition-
ally disabled. Enabled =
Azalia will be uncondition-
ally enabled. Auto = Azalia
will be enabled if present
disabled otherwise.

Audio Controller

This item controls the detection of the Azalia device.

Disabled

Azalia will be unconditionally disabled.
Enabled

Azalia will be unconditionally enabled.
Auto

Azalia will be enabled automatically.

Azalia HDMI Codec

Enable or disable the internal HDMI codec for Azalia.

DP/HDMI Port B

Enable or disable the DP/HDMI Port B.

Summary of Contents for BT700





















































Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands

DFI BT700, User Manual

Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands