DFI BT700 User Manual Download Page 24

Page: 24 / 52

www.dfi .com

Chapter 3 BIOS Setup

Chapter 3

CSM Configuration

This section configures the CSM settings.

Compatibility Support Module Confi guration

CSM Support

CSM16 Module Version

Boot option fi lter

Option ROM execution order

Network
Storage
Video
Other PCI devices

Advanced

[Enabled]

07.71

[UEFI and Legacy]

[Do not launch]
[Legacy only]
[Legacy only]
[UEFI only]



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

Enable/Disable CSM
support

CSM Support

This field is used to enable or disable the CSM support.

Boot option filter

This option controls Legacy/UEFI ROMs priority.

Network

This field controls the execution of UEFI and Legacy PXE OpROM.

Storage

This field controls the execution of UEFI and Legacy Storage OpROM.

Video

This field controls the execution of UEFI and Legacy Video OpROM.

Other PCI devices

This field determines OpROM execution policy for devices other than network, storage

or video.

Security Device Support

This field is used to enable or disable BIOS supporting for the security device. O.S will

not show the security device. TCG EFI protocol and INT1A interface will not be

available.

Trusted Computing

This section configures settings relevant to Trusted Computing innovations.

Enables or Disables
BIOS support for security
device. O.S. will not show
Security Device. TCG
EFI protocol and INT1A
interface will not be
available.

Confi guration

Security Device Support

Current Status Information
No Security Device Found

Advanced

[Disable]



Select Screen



Select Item

Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Reset
ESC: Exit

Summary of Contents for BT700





















































Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands

DFI BT700, User Manual

Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands