DFI BT700 User Manual Download Page 14

Page: 14 / 52

www.dfi .com

Chapter 2 Hardware Installation

Chapter 2

Signal

Pin#

Pin Type

Pwr Rail /Tolerance

BT700

Carrier Board

Description

AC Coupling capacitor

SATA0_RX-

AC Coupling capacitor

SATA0_TX-

AC Coupling capacitor

SATA1_RX-

AC Coupling capacitor

SATA1_TX-

AC Coupling capacitor

SATA_ACT#

O OC 3.3V

3.3V/3.3V

Serial ATA Led. Open collector output pin driven during SATA command activity.

Signal

Pin#

Pin Type

Pwr Rail /Tolerance

BT700

Carrier Board

Description

USB_P0-

USB_P1-

USB_P2-

USB_P3-

USB_P4-
USB_SSRX1-

USB_P5-
USB_SSTX1-

USB_P6-
USB_SSRX0-

AC Coupling capacitor

USB_P7-
USB_SSTX0-

AC Coupling capacitor

USB_0_1_OC#

I CMOS

3.3V Suspend/3.3V

PU 10K to 3.3V Suspend

Connect to Overcurrent of USB Power Switch

Over current detect input 1. This pin is used to monitor the USB power over current of the USB Ports 0 and 1.

USB_2_3_OC#

I CMOS

3.3V Suspend/3.3V

PU 10K to 3.3V Suspend

Connect to Overcurrent of USB Power Switch

Over current detect input 2. This pin is used to monitor the USB power over current of the USB Ports 2 and 3.

USB_4_5_OC#

I CMOS

3.3V Suspend/3.3V

PU 10K to 3.3V Suspend

Connect to Overcurrent of USB Power Switch

Over current detect input 3. This pin is used to monitor the USB power over current of the USB Ports 4 and 5.

USB_6_7_OC#

I CMOS

3.3V Suspend/3.3V

PU 10K to 3.3V Suspend

Connect to Overcurrent of USB Power Switch

Over current detect input 4. This pin is used to monitor the USB power over current of the USB Ports 6 and 7.

USB_ID

I CMOS

3.3V Suspend/3.3V

USB ID pin.Configures the mode of the USB Port 1. If the signal is detected as being 'high active' the BIOS will automatically configure USB Port 1 as USB Client and
enable USB Client support. This signal should be driven as OC signal by external circuitry.

USB_CC

I CMOS

3.3V Suspend/3.3V

USB Client Connect pin.If USB Port 1 is configured for client mode then an externally connected USB host should set this signal to high-active in order to properly make
the connection with the module's internal USB client controller.
If the external USB host is disconnected, this signal should be set to low-active in order to inform the USB client controller that the external host has been
disconnected.
A level shifter/protection circuitry should be implemented on the carrier board for this signal.

Signal

Pin#

Pin Type

Pwr Rail /Tolerance

BT700

Carrier Board

Description

SDIO_CD#

I/O CMOS

3.3V/3.3V

Connect to SD Card

SDIO Card Detect. This signal indicates when a SDIO/MMC card is present.

SDIO_CLK

O CMOS

3.3V/3.3V

Connect to SD Card

SDIO Clock. With each cycle of this signal a one-bit transfer on the command and each data line occurs. This signal has maximum frequency of 48 MHz.

SDIO_CMD

I/O OD/PP CMOS

3.3V/3.3V

Connect to SD Card

SDIO Command/Response. This signal is used for card initialization and for command transfers. During initialization mode this signal is open drain. During command
transfer this signal is in push-pull mode.

SDIO_LED

O CMOS

3.3V/3.3V

SDIO LED. Used to drive an external LED to indicate when transfers occur on the bus.

SDIO_WP

I/O CMOS

3.3V/3.3V

Connect to SD Card

SDIO Write Protect. This signal denotes the state of the write-protect tab on SD cards.

SDIO_PWR#

O CMOS

3.3V/3.3V

SDIO Power Enable. This signal is used to enable the power being supplied to a SD/MMC card device.

SDIO_DAT0-7

48-55

I/O PP CMOS

3.3V/3.3V

SDIO_DAT4-7 NC

Connect to SD Card

SDIO Data lines. These signals operate in push-pull mode

Signal

Pin#

Pin Type

Pwr Rail /Tolerance

BT700

Carrier Board

Description

HDA_RST#
I2S_RST#

O CMOS

3.3V/3.3V

Connect to CODEC

HD Audio/AC'97 Codec Reset.
Multiplexed with I2S Codec Reset.

HDA_SYNC
I2S_WS

O CMOS

3.3V/3.3V

Connect to CODEC

Serial Bus Synchronization.
Multiplexed with I2S Word Select from Codec.

HDA_BCLK
I2S_CLK

O CMOS

3.3V/3.3V

Connect to CODEC

HD Audio/AC'97 24 MHz Serial Bit Clock from Codec.
Multiplexed with I2S Serial Data Clock from Codec.

HDA_SDO
I2S_SDO

O CMOS

3.3V/3.3V

Connect to CODEC

HD Audio/AC'97 Serial Data Output to Codec.
Multiplexed with I2S Serial Data Output from Codec.

HDA_SDIN
I2S_SDI

I CMOS

3.3V/3.3V

Connect to CODEC

HD Audio/AC'97 Serial Data input to Codec.
Multiplexed with I2S Serial Data Input from Codec.

Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector
Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector

USB

USB Interface Signals

Universal Serial Bus Port 0 differential pair.

I/O USB

Universal Serial Bus Port 2 differential pair.

Serial ATA Interface Signals

I SATA

O SATA

I SATA

SATA

Connect to SATA0 Conn TX pin

Universal Serial Bus Port 5 differential pair.
Multiplexed with transmit signal differential pairs for the Superspeed USB data path.

Universal Serial Bus Port 6 differential pair.
Multiplexed with receive signal differential pairs for the Superspeed USB data path.

USB

O SATA

Serial ATA channel 0, Receive Input differential pair.

Serial ATA channel 1, Receive Input differential pair.

Serial ATA channel 0, Transmit Output differential pair.

Serial ATA channel 1, Transmit Output differential pair.

Connect to SATA0 Conn RX pin

Connect to SATA1 Conn TX pin

Connect to SATA1 Conn RX pin

Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector
Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector

Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector

Connect 90

ಳ

@100MHz Common Choke in series and ESD suppressors to GND to USB

connector

Connect Common Choke in series and ESD suppressors to GND to USB connector(This Port is
BOM Option with USB_P6 / USB_P7)

Universal Serial Bus Port 3 differential pair.

Universal Serial Bus Port 7 differential pair.
Multiplexed with transmit signal differential pairs for the Superspeed USB data path.

I/O USB

I/O USB
I USB

SDIO Interface Signals

High Definition Audio Signals/AC'97

I/O USB
O USB

I/O USB
I USB

I/O USB
O USB

Universal Serial Bus Port 1 differential pair.This port may be optionally used as USB client port.

Universal Serial Bus Port 4 differential pair.
Multiplexed with receive signal differential pairs for the Superspeed USB data path.

Summary of Contents for BT700





















































Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands

DFI BT700, User Manual

Search results

Summary of Contents for BT700

Reviews:

Related manuals for BT700

Brands by name

Popular brands