DFI-ITOX 586ITOX User Manual Download Page 90

Page: 90 / 91

586ITOX System Board Users Manual

Serial Port

The serial device (modem, printer) doesnt output anything or is

outputting garbled characters.

1. Make sure that the serial devices power is turned on and that

the device is on-line.

2. Verify that the device is plugged into the correct serial port on

the rear of the computer.

3. Verify that the attached serial device works by attaching it to a

serial port that is working and configured correctly. If the serial

device does not work, either the cable or the serial device has a

problem. If the serial device works, the problem may be due to

the onboard I/O or the address setting.

4. Make sure the COM settings and I/O address are configured

correctly.

Keyboard

Nothing happens when a key on the keyboard was pressed.

1. Make sure the keyboard is properly connected.

2. Make sure there are no objects resting on the keyboard and

that no keys are pressed during the booting process.

System Board

1. Make sure the add-in card is seated securely in the expansion

slot. If the add-in card is loose, power off the system, re-install

the card and power up the system.

2. Check the jumper settings to ensure that the jumpers are

properly set.

3. Verify that all SIMMs are seated securely into the SIMM sockets.

4. Make sure the SIMMs are in the correct locations.

Summary of Contents for 586ITOX




























































































Search results

Summary of Contents for 586ITOX

Reviews:

Related manuals for 586ITOX

Brands by name

Popular brands

DFI-ITOX 586ITOX, User Manual

Search results

Summary of Contents for 586ITOX

Reviews:

Related manuals for 586ITOX

Brands by name

Popular brands