Dexter Laundry 200SHS2.5, Instruction Manual

Page: 127 / 188

FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
111
ПОДРОБНАЯ СХЕМА
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
127
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
111
ПОДРОБНАЯ СХЕМА
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION
160
WARNING: Do not continue to use the sander with a sanding paper
that is overworn or damaged.
WARNING: Do not use the same sanding paper for wood and metal.
Metal particles become embedded in the sanding paper and will
scour a wooden surface.
WARNING: Take care to regularly clean out the build up of dust on the
base underneath the sanding paper and not to let the sanding paper
GRIT CHART
Grit Type Example of use
60 or less
Very Coarse
Material removal, heavy paint removal,
shaping wood
80 – 100 Coarse
Paint removal, rough surface preparation
(e.g. non-planed wood)
120 – 150 Medium Surface preparation planed wood
180 – 220 Fine
Sanding between coats
240 or more Very Fine
Final finishing
Select the required grade of sanding paper.
Remove any dust or debris from the hook and loop of the base.
To attach hook & loop type sanding paper simply align the holes in the sanding paper
To remove the sanding paper, peel it away from the base.
Ordinary (non Hook & Loop type) sanding paper can also be used.
Release the sandpaper clamp from both sides of the sander.
Insert the end of the sandpaper under one clamp and pull the paper tight over the base
ensuring the holes align with those in the base and then clamp the other side.
The sanding paper should be kept tightly clamped over the base, otherwise there could
be excessive wear of the base material.
1.
2.
3.
4.
5.
6.
7.
8.
power point before making any adjustment.
Attaching sanding paper
wear completely down before replacing it. Failure to observe these two
precautionary measures can lead to damage to the hooks and loops on the
base and the sanding paper will not attach properly.
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION
160
WARNING: Do not continue to use the sander with a sanding paper
that is overworn or damaged.
WARNING: Do not use the same sanding paper for wood and metal.
Metal particles become embedded in the sanding paper and will
scour a wooden surface.
WARNING: Take care to regularly clean out the build up of dust on the
base underneath the sanding paper and not to let the sanding paper
GRIT CHART
Grit Type Example of use
60 or less
Very Coarse
Material removal, heavy paint removal,
shaping wood
80 – 100 Coarse
Paint removal, rough surface preparation
(e.g. non-planed wood)
120 – 150 Medium Surface preparation planed wood
180 – 220 Fine
Sanding between coats
240 or more Very Fine
Final finishing
Select the required grade of sanding paper.
Remove any dust or debris from the hook and loop of the base.
To attach hook & loop type sanding paper simply align the holes in the sanding paper
To remove the sanding paper, peel it away from the base.
Ordinary (non Hook & Loop type) sanding paper can also be used.
Release the sandpaper clamp from both sides of the sander.
Insert the end of the sandpaper under one clamp and pull the paper tight over the base
ensuring the holes align with those in the base and then clamp the other side.
The sanding paper should be kept tightly clamped over the base, otherwise there could
be excessive wear of the base material.
1.
2.
3.
4.
5.
6.
7.
8.
power point before making any adjustment.
Attaching sanding paper
wear completely down before replacing it. Failure to observe these two
precautionary measures can lead to damage to the hooks and loops on the
base and the sanding paper will not attach properly.