background image

IOLite LX Quick Start

TECHNICAL REFERENCE MANUAL

15. Safety instructions

Your safety is our primary concern! Please be safe!

15.1 Safety symbols in the manual

Warning

Calls attention to a procedure, practice, or condition that could cause the body injury or death

Caution

Calls attention to a procedure, practice, or condition that could possibly cause damage to
equipment or permanent loss of data.

15.2. General Safety Instructions

Warning

The following general safety precautions must be observed during all phases of operation, service, and
repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in
this manual violates safety standards of design, manufacture, and intended use of the product.
Dewesoft GmbH assumes no liability for the customer’s failure to comply with these requirements.

All accessories shown in this document are available as an option and will not be shipped as standard
parts.

15.2.1. Environmental Considerations

Information about the environmental impact of the product.

15.2.2. Product End-of-Life Handling

Observe the following guidelines when recycling a Dewesoft system:

15.2.3. System and Components Recycling

Production of these components required the extraction and use of natural resources. The substances
contained in the system could be harmful to your health and to the environment if the system is
improperly handled at its end of life! Please recycle this product in an appropriate way to avoid
unnecessary pollution of the environment and to keep natural resources.

This symbol indicates that this system complies with the European Union’s requirements
according to Directive 2002/96/EC on waste electrical and electronic equipment (WEEE).
Please find further information about recycling on the Dewesoft web site

www.dewesoft.com

Restriction of Hazardous Substances

IOLite LX Quick Start V21-1

28/32

Summary of Contents for IOLite LX

































Reviews: