DeWalt DW714 B5 Page 19 Original Instructions Manual Download

Page: 19 / 40

ENGLISH

Switching On and Off (Fig. 24)

A hole (y) is provided in the on/ off switch (l) for insertion of a padlock to

lock the tool.
1. To run the tool, press the on/off switch (l).
2. To stop the tool, release the switch.

Body and Hand Position

Proper positioning of your body and hands when operating the mitre

saw will make cutting easier, more accurate and safer.

  •  Never place your hands near the cutting area.
  •  Place your hands no closer than 150 mm from the blade.
  •  Hold the workpiece tightly to the table and the fence when cutting.

Keep your hands in position until the switch has been released and

the blade has completely stopped.

• Always make dry runs (without power) before finish cuts so that

you can check the path of the blade.

  •  Do not cross your hands.
  •  Keep both feet firmly on the floor and maintain proper balance.
  •  As you move the saw arm left and right, follow it and stand slightly

to the side of the saw blade.

• View through the guard louvres when following a pencil line.

BASIC SAW CUTS
Vertical Straight Cross Cut (Fig. 1, 2, 25)

NOTE:

Always use 254 mm saw blades with 30 mm (

NOTE:

some

regions are 25.4 mm) arbor holes to obtain the desired cutting

capacities.
1. Loosen the mitre lock knob (e) and depress the mitre detent (t) to

release the mitre arm.

2. Engage the mitre latch at the 0° position and tighten the mitre lock

knob (e).

3. Place the wood to be cut against the fence (c, v).
4. Take hold of the operating handle (a) and depress the head lock up

release lever (cc) to release the head.

5. Press the trigger switch (l) to start the motor.
6. Depress the head to allow the blade to cut through the timber and

enter the plastic kerf plate (s).

7. After completing the cut, release the switch and wait for the saw

blade to come to a complete standstill before returning the head to

its upper rest position.

Vertical Mitre Cross-cuts (Fig. 1, 2, 26)

1. Loosen the mitre lock knob (e) and depress the mitre detent (t).

Move the head left or right to the required angle.

2. The mitre detent will automatically locate at 0º, 15º, 22.5º , 30º and

45º. if any intermediate angle or 52º is required hold the head firmly

and lock by tightening the mitre lock knob (e).

3. Always ensure that the mitre lock lever is locked tightly

before cutting.

4. Proceed as for a vertical straight cross-cut.

WARNING:

When mitring the end of a piece of wood with

a small off-cut, position the wood to ensure that the off-

cut is to the side of the blade with the greater angle to the

fence; i.e. left mitre, off-cut to the right - right mitre, off-cut

to the left.

Bevel Cuts (Fig. 1, 2, 27)

Bevel angles can be set from 0º right to 45° left and can be cut with the

mitre arm set between zero and a maximum of 45° mitre position right

or left.
1. Loosen the left side fence clamping knob (k) and slide the upper

part of the left side fence (v) to the left as far as it will go. Loosen

the bevel clamp knob (p) and set the bevel as desired.

2. Tighten the bevel clamp knob (p) firmly.
3. Proceed as for a vertical straight cross-cut.

Quality of Cuts

The smoothness of any cut depends on a number of variables, e.g. the

material being cut. When smoothest cuts are desired for moulding and

other precision work, a sharp (60 tooth carbide) blade and a slower for

wood, a sharp (80-120 tooth carbide) blade and a slower for aluminum,

even cutting rate will produce the desired results.

WARNING:

Ensure that the material does not creep while

cutting; clamp it securely in place. Always let the blade

come to a full stop before raising the arm. If small fibres

of wood still split out at the rear of the workpiece, stick a

piece of masking tape on the wood where the cut will be

made. Saw through the tape and carefully remove tape

when finished.

Clamping the Workpiece (Fig. 3, 7, 38)

1. Whenever possible, clamp the wood/ aluminum to the saw.
2. For best results use the clamp (gg) made for use with your saw.

Clamp the workpiece to the fence whenever possible. You can

clamp to either side of the saw blade; remember to position your

clamp against a solid, flat surface of fence.

3. Mounting the clamp (Fig. 7, 38):
Inserting the vertical clamp to the holes (mm) as shown in Figure 7,

then rotate to the right position.

If horizontal clamp is needed, please mounting the horizontal clamp

to the holes (qq) as shown in Figure 38.

WARNING:

Always use a material clamp when cutting

non-ferrous metals.

WARNING:

Always use both of vertical clamp and

horizontal clamp when cutting small pieces.

Support for Long Pieces (Fig. 3, 8)

1. Always support long pieces.
2. For best results, use the extension work support (ii) to extend

the table width of your saw. Support long workpieces using any

convenient means such as saw-horses or similar devices to keep

the ends from dropping.

  3. Mounting the work support (Fig. 8):
     •  Use the supplied blade wrench (i) to loosen the screws.
    •  Insert the work support to the holes (h).
    •  Tighten the screws.

Cutting Aluminum Extrusion (Fig. 28)

WARNING:

Never attempt to cut thick or round aluminum

extrusions. Thick aluminum extrusions may come loose

during operation and round aluminum extrusions cannot be

secured firmly with this tool.

When securing aluminum extrusions, use spacer blocks or pieces

of scrap as shown in the Figure 28 to prevent deformation of the

aluminum.Use a cutting lubricant when cutting the aluminum extrusion

to prevent build-up of the aluminum material on the blade.

Cutting Picture Frames, Shadow Boxes and

Other Four-sided Projects (Fig. 29, 30)