![background image](http://html.mh-extra.com/html/dewalt/dcmasps5/dcmasps5_original-instructions-manual_86644016.webp)
14
English
Protecting the Environment
w
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that
can be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com
.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
Replacement chain and bar are available from your
nearest authorized service center.
• This chain saw requires replacement 204 mm chain DT20681.
Replacement 204 mm bar and chain DT20686.
Optional Accessories
WARNING:
Since accessories, other than those offered
by
D
e
WALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT
recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Saw Chain and Guide Bar
After every few hours of use, remove the sprocket cover, guide
bar and chain and clean thoroughly using a soft bristle brush.
Ensure oiling hole on bar is clear of debris. When replacing dull
chains with sharp chains it is good practice to flip the chain bar
from bottom to top.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
D
Cleaning
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
C
Lubrication
Your power tool requires no additional lubrication.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING:
To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start‑up can cause injury.
The charger and battery pack are not serviceable.
Saw Chain Sharpness
CAUTION:
Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can cut
you when it is not running.
IMPORTANT:
The chain cutters will dull immediately if they
touch the ground, stones, masonry or a nail while cutting.
To get the best possible performance from your chain saw it
is important to keep the teeth of the saw chain sharp. Chain
sharpening services are available from your nearest
D
e
WALT
service center.
nOTE:
Each time the saw chain is sharpened, it loses some
of the reduced kickback qualities and extra caution should be
used. It is recommended that a saw chain be sharpened no
more than four times.
bar
6
to make this cut. Cut 1/3 through diameter of limb.
Then make the finish cut from the top. If you try to cut off
thick branches from the bottom, the branch may close
in and pinch the saw chain in the cut. If you try to cut off
thick branches from the top, without a shallow undercut,
the branch may splinter. Do not force pole saw. The motor
will overload and can burn out. It will do the job better and
safer at the rate for which it was intended.
c. Remove pole saw from cut while it is running at full speed.
Stop pole saw by releasing trigger switch
33
. Make sure
saw chain has stopped before setting pole saw down.
Summary of Contents for DCMASPS5
