background image

English

12

Troubleshooting Guide

if the fittings will not seal properly:

• 

Check to see if the expander head is screwed 
on tightly.

 

-

Tighten the head.

• 

Check to see if the exapnder head segments are bent 
or misaligned.

 

-

Replace the expander head.

• 

Are the expander head segments not properly 
contracting between expansions?

 

-

Clean and relubricate the expander head.

 

-

Check to see if the expander cone is 
properly lubricated.

 

-

Clean and relubricate the expander cone.

• 

has the fitting been damaged?

 

-

Replace the fitting.

• 

Was the PEX tubing removed while the expander 
cone was in the expanded postion?

 

-

Cut 2" (50 mm) from the PEX tubing and restart 
the process.

• 

is the PEX tubing and Ring dry?

 

-

Wipe dry with a clean, lint-free cloth.

• 

is there grease from the expander head inside the 
PEX tubing?

 

-

Wipe off all grease from inside the PEX tubing and 
relubricate the expander head.

The Ring slides during the expansion process:

• 

is the PEX tubing and Ring dry?

 

-

Wipe dry with a clean, lint-free cloth

• 

Are your hands clean and dry?

 

-

Make sure your hands are clean and dry. Oils from 
your hands can lubricate the PEX tubing and Ring.

• 

is the Ring being held properly in place?

 

-

Use your thumb to hold the ring in place for the first 
couple of exapansions.

Summary of Contents for DCE400B













Reviews: