ENGLISH
29
EC-Declaration of Conformity
Radio Equipment Directive
DEWALT Rotary Laser
DCE074R, DCE079R, DCE079G
DEWALT hereby declares that the DEWALT Rotary Laser
DCE074R/DCE079R/DCE0709G is in compliance with the
Directive 2014/53/EU and to all applicable EU directive
requirements.
The full text of the EU Declaration of Conformity can be
requested at DEWALT Industrial Tool Co., DEWALT Europe,
DEWALT D-655-10 Idstein, Germany 65509 or is available at
the following internet address: www.2helpU.com.
Search by the Product and Type Number indicated on the
nameplate.
READ ALL INSTRUCTIONS
Batteries and Power
This
D
e
WALT
rotary laser will accept all
D
e
WALT
18 volt
lithium ion batteries, but is built to best resist damage during a
fall when used with the following batteries: All 1.5Ah and 2Ah
D
e
WALT
18 volt lithium ion batteries.
Charging the Battery
The battery pack is not fully charged out of the carton. You
need to use a
D
e
WALT
18 volt charger to charge the battery
pack before you can use the rotary laser.
• Refer to the chart at the end of this manual for compatibility
of chargers and battery packs.
• Be sure to read all safety instructions before using your
charger.
WARNING:
• DO NOT attempt to charge the battery pack
with any chargers other than the ones listed
in this manual.
The charger and battery pack are
specifically designed to work together.
• Carefully follow all instructions and warnings on
the battery label and package and accompanying
Battery Safety Manual
.
1. Slide the battery pack into the charger as described in the
Battery Safety Manual
.
2. Wait until the battery pack is
fully charged
.
3. Slide the battery pack out of the track.
NOTE:
When ordering replacement battery packs, be sure to
include the catalog number and voltage.
Installing the 18V
D
e
WALT
Battery Pack
1. Position the fully-charged 18V
D
e
WALT
battery pack so the
release button (Figure
E
15
) is facing away from you and
to the right.
2. Press and hold down the release button on the battery
pack.
3. Slide the battery pack all the way into the track on the side
of the laser.
4. Release the button on the battery pack.
Removing the Battery Pack
1. Press and hold the release button on the battery pack.
2. Slide the battery pack out of the track on the laser.
3. Release the button on the battery pack.
4. To recharge the battery pack, insert it into the charger, as
described in the
Battery Safety Manual
.
WARNING:
Batteries can explode or leak, and can
cause injury or fire. To reduce this risk, follow the
instructions in the
Battery Safety Manual
.
Storing Battery Packs
• The best storage place is one that is cool and dry, and
away from direct sunlight and excess heat or cold.
• Long storage will not harm the battery pack or charger.
Under proper conditions, they can be stored for 5 years
or more.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
User Safety
Personal Safety
• Stay alert, watch what you are doing, and use common
sense when operating a laser product. Do not use
the tool while tired or under the influence of drugs,
alcohol, or medication.
A moment of inattention while
operating laser products may result in serious personal
injury.
• Use appropriate personal protective equipment,
including eye protection when working in a construction
environment.
Tool Use and Care
• Do not use the tool if the switch does not turn it on or
off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Store idle laser products out of the reach of children
and do not allow persons unfamiliar with the laser
product or these instructions to operate the laser
product.
Laser products are dangerous in the hands of
untrained users.
• Use only accessories that are recommended by the
manufacturer for your model.
Accessories that may be
suitable for one tool, may become hazardous when used
with another tool.
DW074_DW079 User Manual - EU - APRIL 2018 - TRANSLATED.indd 29
5/17/2018 12:35:32 PM
