background image

16

English

NOTICE:  Risk  of  property  damage.  Drain  water  from  air  tank  may 
contain oil and rust, which can cause stains. 
  6. When air tank pressure gauge reads 10 psi, rotate valve to the 

fully open position.

  7. Close drain valve when finished.

Checking Air Filter Element (Fig. 1)

WARNING:  Hot  surfaces.  Risk  of  burn.  Outlet  tube,  pump  head, 

and surrounding parts are very hot, do not touch. Allow compressor 
to cool prior to servicing. 
  1. Ensure Auto/Off switch (L) is in the 

OFF(O)

 Position.

  2. Allow unit to cool.
  3. Remove filter cover (J) from filter base.            

J

  4. Remove element from filter base.
  5. Place new element back in filter base. Purchase 

replacement  parts  from  your  local  dealer  or 
authorized service center. Always use identical 
replacement parts.

  6. Snap filter cover to filter base. 
NOTICE: Risk of property damage.  Do not operate without air 
inlet filter 

ACCESSOrIES

WARNING: The use of any other accessory not recommended for 

use  with  this  tool  could  be  hazardous.  Use  only  accessories  rated 
equal to or higher than the rating of the air compressor.

Recommended  accessories  for  use  with  your  tool  are  available 
for  purchase  from  your  local  dealer  or  authorized  service  center. 
If  you  need  assistance  in  locating  any  accessory  for  your  tool, 
please  contact  D

e

WALT  Industrial Tool  Co.,  701  East  Joppa  Road, 

Baltimore, MD 21286, call 1-800-4-D

e

WALT (1-800-433-9258) or visit 

our website www.dewalt.com.

SErVICE INFOrMATION

Please have the following information available for all service calls: 
Model Number ____________ Serial Number _________________
Date and Place of Purchase ______________________________

repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance 

and adjustment should be performed by a D

e

WALT factory service 

center,  a  D

e

WALT  authorized  service  center  or  other  qualified 

service personnel. Always use identical replacement parts.

Full One Year Warranty

D

e

WALT heavy duty industrial tools are warranted for one year from 

date of purchase. We will repair, without charge, any defects due to 
faulty materials or workmanship. For warranty repair information, call 
1-800-4-D

e

WALT (1-800-433-9258). This warranty does not apply to 

accessories or damage caused where repairs have been made or 
attempted by others. This warranty gives you specific legal rights and 
you may have other rights which vary in certain states or provinces.
lAtIn  AMerICA:  This  warranty  does  not  apply  to  products  sold 
in  Latin  America.  For  products  sold  in  Latin  America,  see  country 
specific warranty information contained either in the packaging, call 
the local company or see website for warranty information.

Summary of Contents for D55371






















Reviews: