ENGLISH
26
Service Indicator LED (fi g. 2)
The red service indicator LED (c) lights up when
the carbon brushes are nearly worn out to indicate
that the tool needs servicing. After a further 8 hours
of use the motor will automatically be shut off. The
carbon brushes are not user-serviceable. Take the
tool to an authorised D
E
WALT repair agent.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your D
E
WALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING:
115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING:
No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data).
The minimum conductor size is 1.5 mm
2
. When
using a cable reel, always unwind the cable
completely.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source
before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Inserting and Removing SDS Max
®
Accessories (fi g. 3, 4)
This machine uses SDS Max
®
chisels (refer to the
inset in figure 4 for a cross-section of an SDS Max
®
bit shank).
1. Clean and grease the bit shank.
WARNING:
Only apply a slight amount
of lubricant to the bit shank. Do not
apply lubricant to the machine.
2. Insert the bit shank into the tool holder (f), and
press and turn the bit slightly until the sleeve
snaps into position.
3. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
4. To remove a bit pull back the tool holder locking
sleeve (f) and pull the bit out of the tool holder.
Indexing the Chisel Position (fi g. 5, 6)
The chisel can be indexed and locked into 8 different
positions.
1. Press the safety lock (e) and rotate the mode
selector (d) until it points rearward. Release the
safety lock.
2. Rotate the chisel in the desired position.
3. Press the safety lock (e) and rotate the mode
selector (d) back to the forward position
indicated by the hammering symbol.
4. Release the safety lock and check that the
mode selector switch is locked in place.
5. Twist the chisel until it locks in position.
Setting the Electronic Speed and
Impact Control Dial (fi g. 2)
Turn the dial (b) to the desired level. The higher the
number, the greater the speed and impact energy.
With dial settings from 1 (low) to 7 (full power) the
Summary of Contents for D25830
