Devantech dS2832 User Manual Download Page 3 | Manualshive

Page: 3 / 68

background image

dS28

dS28

32

32

User Manual v4.10

Modbus Gateway......................................................................................................56

Loading the application firmware.................................................................................................57

Erasing old configuration settings...............................................................................59

dS2832 hardware......................................................................................................................60

LED indication..........................................................................................................61
Power supply...........................................................................................................61

Operating temperature..............................................................................................61
Power relays............................................................................................................62

Analogue/Digital flexible I/O's....................................................................................63

Connection examples.................................................................................................................63

Temperatue sensor...........................................................................................................64
Power supply input voltage................................................................................................64

Analogue channels............................................................................................................64

Serial port connections..............................................................................................66

dS2832 dimensions...................................................................................................................67
Notes......................................................................................................................................68

Documentation history

V4.06

First release of the dS2832 manual.

V4.07

Added new features:
Ping

Used to ping other machines to check if responding.

Sequencer

Added a 120 step, 12 output sequencer

v4.08

Added display of MAC address to network configuration page.
Bugfix – NTP (Real time clock) startup failed under some circumstances.

Renamed command “counters” to “setcounters”.

V4.09

Added 3 new commands to Binary and AES Binary command set, to
control all relays in one command. Set all, set selected and clear selected.

V4.10

Added support for dSx42 extension modules.

Note:

If you have a custom app based on app-dSxxxx-v4-07 or earlier, you will need to re-

name the “counters” command to “setcounters” for it to compile with this version.

Copyright

© 2016-2022,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

3

«
1
2
3
4
5
...
»

Summary of Contents for dS2832





































































Reviews:

No comments

Related manuals for dS2832

Brand: P&E Microcomputer Systems Pages: 53

Brand: Gigabyte Pages: 96

Brand: J&W Pages: 37

Brand: ECS Pages: 52

Brand: Zotac Pages: 56

Brand: JETWAY Pages: 52

microComponents mp6-XEVA

Brand: Bartels Mikrotechnik Pages: 9

Brand: Texas Instruments Pages: 25

Brand: ISSC Pages: 39

Brand: Infineon Pages: 20

Brand: Biostar Pages: 63

Brand: Renesas Pages: 30

Brand: EVGA Pages: 1

Brand: Abit Pages: 72

Brand: Maxus Pages: 59

Brand: BOSER Technology Pages: 38

Brand: Gigabyte Pages: 44

ATX-KLS0 Series

Brand: Quanmax Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands