Devantech dS2824 User Manual Download Page 23 | Manualshive

Page: 23 / 64

background image

dS2824

dS2824

User Manual v4.09

Pinging remote machines

The ping module allows you to check other machines are still online and responding.
Ping threads are only started a boot time if the Repeat Time is greater than zero. Also DNS

lookup is only performed once at boot time if the Repeat Time is greater than zero. So after
making changes, wait for the Update Pending light to go out (5 seconds after last change) and

reboot the module.

Repeat Time

This is how often the ping is repeated, in seconds. 10 sends a ping every 10 seconds.

Attempts

The number of failed pings (no response) before failure is reported by setting the ping time to
zero. If set to 5 it will take 5 consecutive failed responses to trigger a failure. If a response is

received, say on the 3

rd

try, the attempt counter is reset to 5.

Copyright

© 2016-2021,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

23

«
...
21
22
23
24
25
...
»

Summary of Contents for dS2824

































































Reviews:

No comments

Related manuals for dS2824

Brand: W&T Pages: 30

Brand: OEZ Pages: 12

HR1S-DMB Series

Brand: IDEC Pages: 16

Brand: Omron Pages: 12

Brand: ABB Pages: 124

Brand: GAPOSA Pages: 16

Brand: Omega Pages: 2

Brand: ABB Pages: 27

Brand: ABB Pages: 40

Brand: U-Prox Pages: 3

Brand: Extreme Max Pages: 5

Brand: ABB Pages: 12

Brand: Konica Minolta Pages: 16

ZM SINGLE RELAY

Brand: Heatit Pages: 6

Brand: Allis-Chalmers Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands