background image

7

Maintenance:

Iron at maximal temperature 110 

°

C, carefully with steam.

We recommend delicate washing at 40

°

C

All closures (zippers, press buttons, velcros, buttons, carabines) must be properly closed
to avoid abrasion

Before washing and drying is necessary to remove neoprene knee pads!

PH of washing bath must not be higher than 9

.

Do not use detergents with bleaching effects.

Optimal level of machine loading is 2/3, with maximum possible water level and lower
spinning speeds.

If the garment has removable insert, always wash the outer parts separately from inserts.
If inserts are not soiled, remove them and wash just the outer parts to prevent
unnecessary wear of moisture and thermal barrier.

Do not use any softeners!

Line dry is optimal

Using a tumbler dryer, dry at lower temperature. We recommend drying in two cycles
(face and back sides) 2 x 45 minutes.

A dryer should be filled at 2/3 of its capacity. (f.e. for drum of 13 kg put dry garments with
weight of 10 kg)

If the garment is damp, we recommend to hang it to dry

To recover the treatment we recommend additional drying at 70

°

C for 15 minutes

!!

Perform the additional drying on closed garment from the face side after each
maintenance (w drying).

Summary of Contents for GEPARD MAX











Reviews: