Detex ADVANTEX 82 Series Installation Instructions Manual Download

Page: 17 / 18

FIRE RATED TOP ROD ONLY (TRO) DOORS

3/4" Dia. Min.

1-1/4" Deep min.

Retaining Clip

Popper

Cap Plug

12"

9/16" Dia. Min.

1-5/8" Deep min.

A door locking popper is required when a fire door utilizes a top latching mechanism only

(TRO). The popper is designed to project a spring loaded bolt into the adjacent frame or door
in the event of fire. Detex recommends installing the popper in the edge of the door 12" above

the threshold or finished floor.

Holes for the popper and plug must be aligned with each other.

NOTE:

Door/Frame reinforcement is required where

popper and cap plug are to be installed.

104888 Page 17

STEP 14:

COVER INSTALLATIONS

STEP 15:

DOOR POPPER INSTALLATION

Install endcap with two screws

to match finish

Install cover with four screws to

match finish

Summary of Contents for ADVANTEX 82 Series



















Search results

Summary of Contents for ADVANTEX 82 Series

Reviews:

Related manuals for ADVANTEX 82 Series

Brands by name

Popular brands

Detex ADVANTEX 82 Series, Installation Instructions Manual

Search results

Summary of Contents for ADVANTEX 82 Series

Reviews:

Related manuals for ADVANTEX 82 Series

Brands by name

Popular brands