Detex ADVANTEX 60 Series Installation Instructions Manual Download

Page: 15 / 18

BOTTOM STRIKE HOLE LOCATION & DRILLING

With door closed

use tip of bolt to
mark location

for strike

Place strike centered in hole,
mark then drill holes for strike
mounting screws and secure

strike with two screws

Drill 1" hole for

strike (depth - 3/4")

Top strike pocket

Begin strike installation with
notched side of pocket towards
inside door face. If additional
adjustment is needed, rotate

Door stop

Door frame header

104884 Page 15

NOTE:
1. If using threshold, drill 5/8" hole.

Door stop side

Tilt strike pocket
to fit into cutout

Finished strike installation view

Door frame
header

STEP 11:

TOP STRIKE INSTALLATION

STEP 12:

BOTTOM STRIKE INSTALLATION

(Disregard if TRO device is being installed)

Top strike pocket

Shim

Strike insert

12a

12c

12b

Summary of Contents for ADVANTEX 60 Series



















Search results

Summary of Contents for ADVANTEX 60 Series

Reviews:

Related manuals for ADVANTEX 60 Series

Brands by name

Popular brands

Detex ADVANTEX 60 Series, Installation Instructions Manual

Search results

Summary of Contents for ADVANTEX 60 Series

Reviews:

Related manuals for ADVANTEX 60 Series

Brands by name

Popular brands