background image

TB-2083

Page 4 of 4

A. Place the 

:

Meg on an insulator (e.g. Teflon or glass)

and press the white test button. Only the first red LED
on the right, marked “On” should be illuminated. If this
LED fails to light, the battery should be replaced before
proceeding.

B. Place the 10G ohm resistor across the middle
electrode and the side electrode as illustrated in 
Figure 7. Press the test button. The second LED
should light. Be sure not to contact the leads or the
buttons as your body’s resistance will affect the
readings.

Figure 7. Calibration of the 

:

Meg

C. Continue this process with each consecutive
resistor, checking to make sure the appropriate LEDs
are illuminated. If all resistors check properly, the unit’s
calibration is verified.

Adjustment

Unauthorized servicing or modifications to the 

:

Meg

will void the product warranty. Servicing should only be
performed by the factory. See warranty section for
repair charges.

RESISTOR

ELECTRODE

Limited Warranty

Desco expressly warrants that for a period of one (1) year
from the date of purchase, Desco 

:

Megs will be free of

defects in material (parts) and workmanship (labor). Within
the warranty period, a unit will be tested, repaired or
replaced at Desco’s option, free of charge. Call Customer
Service at 909-627-8178 (Chino, CA) or 781-821-8370
(Canton, MA) for a Return Material Authorization (RMA)
and proper shipping instructions and address. Any unit
under warranty should be shipped prepaid to the Desco
factory. Include a copy of your original packing slip,
invoice, or other proof of date of purchase. Warranty
replacements will take approximately two weeks.

If your unit is out of warranty call Customer Service at
909-627-8178 (Chino, CA) or 781-821-8370 (Canton, MA)
for a Return Material Authorization (RMA) and proper
shipping instructions and address. Desco will quote repair
charges necessary to bring your unit up to factory
standards. 

Warranty Exclusions

THE FOREGOING EXPRESS WARRANTY IS MADE IN
LIEU OF ALL OTHER PRODUCT WARRANTIES,
EXPRESSED AND IMPLIED, INCLUDING MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE WHICH ARE SPECIFICALLY DISCLAIMED. The
express warranty will not apply to defects or damage due
to accidents, neglect, misuse, alterations, operator error,
or failure to properly maintain, clean or repair products.

Limit of Liability

In no event will Desco or any seller be responsible or
liable for any injury, loss or damage, direct or
consequential, arising out of the use of or the inability to
use the product. Before using, users shall determine the
suitability of the product for their intended use, and users
assume all risk and liability whatsoever in connection
therewith.

DESCO WEST

- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 • Fax (909) 627-7449

DESCO EAST

- 90 Hudson Road, Canton, MA 02021-1407 • (781) 821-8370 • Fax (781) 575-0172 • Web Site: http://www.desco.com

© 2002 DESCO INDUSTRIES INC.

Employee Owned

Summary of Contents for Meg Pocket Megohmmeter

Page 1: ...0 Surface Resistance Test Kit For more information on this product ask for Techical Bulletin TB 3014 Installation Remove the meter from the carton and inspect for damage Each unit should be fully charged and includes 1 Meg Pocket Megohmmeter 1 Surface to Ground cord assembly 1 Installed 9V battery Properly store the megohmmeter and its component assemblies when not in use Operation The Meg will pe...

Page 2: ...ace Residual voltages may cause the two upper range LEDs to light resulting in a false reading When the Surface to Ground cord is plugged in voltage is diverted from the center electrode to the cord in order to measure resistance When making Surface to Ground tests follow these procedures A Check battery operation by depressing the white button The red On lamp will indicate that the unit is functi...

Page 3: ...entiometer the appropriate LED is lit Specifications Sensitivity Range Surface Resistivity Less than 1010 ohms sq Surface to Ground Less than 109 ohms LED Key from right to left 1 Red 1010 Meter On and Battery OK 2 Green 1010 Static Dissipative 3 Green 109 Static Dissipative 4 Green 108 Static Dissipative 5 Green 107 Static Dissipative 6 Yellow 106 7 Yellow 105 Conductive Test Sample Size 3 x 1 1 ...

Page 4: ... and proper shipping instructions and address Any unit under warranty should be shipped prepaid to the Desco factory Include a copy of your original packing slip invoice or other proof of date of purchase Warranty replacements will take approximately two weeks If your unit is out of warranty call Customer Service at 909 627 8178 Chino CA or 781 821 8370 Canton MA for a Return Material Authorizatio...

Reviews: