background image

www.desatech.com

116237-01H

23

FIREPLACE 

INSTALLATION

Continued

CHECKING GAS CONNECTIONS

 WARNING: Test all gas piping 

and connections , internal and 

external to unit, for leaks after 

installing or servicing. Correct 

all leaks at once.

  WARNING:  Never  use  an 

open flame to check for a leak. 

Apply noncorrosive leak detec

-

tion fluid to all joints. Bubbles 

forming show a leak. Correct all 

leaks at once.

pRESSURE TESTING GAS SUppLY 
pIpING SYSTEM 

Test Pressures In Excess Of 1/2 PSIG 
(3.5 kPa)

1.  Disconnect  fireplace  and  its  individual 

equipment shutoff valve from gas supply 
piping system. Pressures in excess of 1/2 
psig (3.5 kPa) will damage fireplace gas 
regulator.

2.  Cap off open end of gas pipe where equip-

ment shutoff valve was connected.

3.  Pressurize supply piping system by either 

opening  propane/LP  supply  tank  valve 
for propane/LP gas fireplace or opening 
main gas valve located on or near gas 
meter for natural gas fireplace or using 
compressed air.

4.  Check all joints of gas supply piping sys-

tem. Apply  noncorrosive  leak  detection 
fluid to all joints. Bubbles forming show a 
leak. Correct all leaks at once.

5.  Reconnect  fireplace  and  equipment 

shutoff valve to gas supply. Check recon-
nected fittings for leaks. 

Test Pressures Equal To or Less Than 
1/2 PSIG (3.5 kPa)

1.  Close equipment shutoff valve (see Fig-

ure 33).

2.  Pressurize supply piping system by either 

opening  propane/LP  supply  tank  valve 
for propane/LP gas fireplace or opening 
main gas valve located on or near gas 
meter for natural gas fireplace or using 
compressed air.

3.  Check all joints from propane/LP supply 

tank  or  gas  meter  to  equipment  shutoff 
valve (see Figure 34 or Figure 35). Ap-
ply  noncorrosive  leak  detection  fluid  to 
all joints. Bubbles forming show a leak. 
Correct all leaks at once.

Figure 33 - Equipment Shutoff Valve

Open

Closed

Equipment 
Shutoff Valve

Figure 34 - Checking Gas Joints for 

Propane/LP Gas Fireplace

Propane/LP 
Supply Tank

Gas Valve

Equipment Shutoff Valve

Figure 35 - Checking Gas Joints for 

Natural Gas Fireplace

Gas Meter

Gas Valve

Equipment 
Shutoff Valve

Figure 32 - Connecting Flexible Gas Line 

to Electronic Valve

1/2" NPT 
Incoming 
Gas Line

Inlet 
Pressure 
Tap

Outlet 
Pressure 
Tap

Equipment 
Shutoff 
Valve

Flexible 
Gas Line 
Do NOT 
Kink

Note: Wire Connections Not Shown for Clarity

Red Surface 
Indicates For 
Propane/LP Use 
Only

Summary of Contents for VVC42NE Series









































Reviews: