background image

3

102490

OWNER’S MANUAL

LOCAL CODES

Install and use heater with care. Follow all
local codes. In the absence of local codes,
use the latest edition of National Fuel Gas
Code ANSI Z223.1, also known as NFPA
54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY  10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA  02269

UNPACKING

1.

Remove heater from carton.

2.

Remove all protective packaging ap-
plied to heater for shipment.

3.

Check heater for any shipping damage.
If heater is damaged, promptly inform
dealer where you bought heater.

PRODUCT
FEATURES

Safety Pilot

This heater has a pilot with an Oxygen
Depletion Sensor Shutoff System (ODS).
The ODS/pilot is a required feature for vent-
free room heaters. The ODS/pilot shuts off
the heater if there is not enough fresh air.

Piezo Ignition System

This heater has a piezo ignitor. This system
requires no matches, batteries, or other
sources to light heater.

Figure 1 - Model VN10T Vent-Free Natural Gas Heater

PRODUCT
IDENTIFICATION

Heater Cabinet

Grill Guard

Burners

Front Panel

Control Knob

Piezo Ignitor Button

AIR FOR
COMBUSTION AND
VENTILATION

Today’s homes are built more energy effi-
cient than ever. New materials, increased
insulation, and new construction methods
help reduce heat loss in homes. Home own-
ers weather strip and caulk around windows
and doors to keep the cold air out and the
warm air in. During heating months, home
owners want their homes as airtight as pos-
sible.

While it is good to make your home energy
efficient, your home needs to breathe. Fresh
air must enter your home. All fuel-burning
appliances need fresh air for proper com-
bustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and
fuel burning appliances draw air from the
house to operate. You must provide ad-
equate fresh air for these appliances. This
will insure proper venting of vented fuel-
burning appliances.

PROVIDING ADEQUATE
VENTILATION

The following is excerpts from National
Fuel Gas Code. NFPA 54/ANSI Z223.1,
Section 5.3, Air for Combustion and Venti-
lation.

All spaces in homes fall into one of the three
following ventilation classifications:

1. Unusually Tight Construction; 2. Uncon-
fined Space; 3. Confined Space.

The information on pages 4 and 5 will help
you classify your space and provide ad-
equate ventilation.

 WARNING: This heater shall

not be installed in a confined
space unless provisions are pro-
vided for adequate combustion
and ventilation air. Read the fol-
lowing instructions to insure
proper fresh air for this and other
fuel-burning appliances in your
home.

Continued

Summary of Contents for Vanguard VN10T





















Reviews: