background image

15

102490

OWNER’S MANUAL

ACCESSORY

Purchase this heater accessory from your
local dealer. If they cannot supply this ac-
cessory, call DESA International’s Parts
Department at 1-800-972-7879 for referral
information. You can also write to the ad-
dress listed on the back page of this manual.

MANUAL SHUTOFF
VALVE - GA5010

Manual shutoff valve
with 1/8" NPT tap.

SERVICE
PUBLICATIONS

You can purchase a service manual from the
address listed on the back page of this
manual. Send a check for $5.00 payable to
DESA International.

When gas pressure is too low

• pilot will not stay lit

• burner(s) will have delayed ignition

• heater will not produce specified heat

When gas quality is bad

• pilot will not stay lit

• burner(s) will produce flames and soot

• heater will backfire when lit

You may feel your gas pressure is too low or
gas quality is bad. If so, contact your local
natural gas supplier.

SERVICE HINTS

Note:

 Use only original replacement parts.

This will protect your warranty coverage for
parts replaced under warranty.

Parts Under Warranty

Contact authorized dealer from whom you
purchased this product. If they cannot sup-
ply original replacement part(s), call DESA
International’s Technical Service Depart-
ment at 1-800-323-5190 for information.

When contacting your dealer or DESA In-
ternational, have ready:

• your name

• your address

• model number of your heater

• how heater was malfunctioning

• type of gas used (propane or natural

gas)

• purchase date

Usually, we will ask you to return the defec-
tive part to the factory.

Parts Not Under Warranty

Contact authorized dealers of this product.
If they cannot supply original replacement
part(s), call DESA International’s Parts
Department at 1-800-972-7879 for referral
information.

When calling DESA International, have
ready:

• model number of your heater

• the replacement part number

REPLACEMENT
PARTS

You may have further questions about in-
stallation, operation, or troubleshooting.

If so, contact DESA International’s Techni-
cal Service Department at 1-800-323-5190.

TECHNICAL
SERVICE

SPECIFICATIONS

VN10T

Btu

10,000

Type Gas

Natural Only

Ignition

Piezo

Pressure Regulator Setting 3.8" W.C.

Inlet Gas Pressure (inches of water)

Maximum

10.5"

Minimum

4"

Dimensions, Inches (H x W x D)

Heater

21 1/2 x 13 1/2 x 7

Carton

24 3/4 x 16 3/4  x 7 1/2

Weight (pounds)

Heater

14

Shipping

18

Summary of Contents for Vanguard VN10T





















Reviews: