background image

6

102490

NATURAL GAS HEATER

VANGUARD VN10T

2.

Mark two mounting screw locations on
wall (see Figure 5).

INSTALLING HEATER TO
WALL

Marking Screw Locations

1.

Determine where you will locate heater.

Figure 5 - Mounting Screw Locations

Mounting

Screw

Locations

10 7/8"

Minimum To

Maintain 8"

Clearance
From Wall

7 3/4"

20 1/4"

Minimum To

Maintain 3"

Clearance

From Floor

FLOOR

JOINING WALL

 WARNING: Maintain minimum

clearances shown in Figure 5. If
you can, provide greater clear-
ances from floor and joining wall.

For convenience and efficiency, install heater

• where there is easy access for opera-

tion, inspection, and service

• in coldest part of room

Figure 4 - Mounting Clearances As Viewed
From Front of Heater

36"

3"

FLOOR

CEILING

Minimum

Minimum To Top Surface 
Of Carpeting, Tile Or Othe
Combustible Material

8"

Minimum
From
Sides Of
Heater

Right
Side

Left
Side

INSTALLING TO
WALL

CHECK GAS TYPE

Use only natural gas. If your gas supply is
not natural, do not install heater. Call dealer
where you bought heater for proper type
heater.

INSTALLATION ITEMS

Before installing heater, make sure you have
the items listed below:

• piping (check local codes)
• sealant (resistant to propane/LP gas)
• manual shutoff valve *
• ground joint union
• test gauge connection * (see Figure

12, page 8)

• sediment trap
• tee joint
• pipe wrench

NOTICE: A qualified service per-
son must install heater. Follow
all local codes.

* An A.G.A. design-certified manual shutoff
valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Pur-
chase the optional A.G.A. design-certified
manual shutoff valve from your dealer. See
Accessory, page 15.

LOCATING HEATER

This heater is designed to be mounted on a
wall.

 WARNING: Maintain the mini-

mum clearances shown in Figure
4. If you can, provide greater clear-
ances from floor, ceiling, and join-
ing wall.

 CAUTION: If you install the

heater in a home garage

• heater pilot and burner must

be at least 18 inches above
floor

• locate heater where moving

vehicle will not hit it

IMPORTANT:

 Vent-free heaters add mois-

ture to the air. Although this is beneficial,
installing heater in rooms without enough
ventilation air may cause mildew to form
from too much moisture. See Air for Com-
bustion and Ventilation, 
pages 3 through 5.

 CAUTION: This heater cre-

ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities in the air (such
as tobacco smoke) exist, may
discolor walls.

 WARNING: Never install the

heater

• in a bathroom
• in a recreational vehicle
• where curtains, furniture,

clothing, or other flammable
objects are less than 36 inches
from the front, top, or sides of
the heater

• as a fireplace insert
• in high traffic areas
• in windy or drafty areas

Minimum To
Top Surface Of
Carpeting, Tile
Or Other
Combustible
Material

Summary of Contents for Vanguard VN10T





















Reviews: