![background image](http://html1.mh-extra.com/html/desa/vanguard-vi33nr/vanguard-vi33nr_owners-operation-and-installation-manual_2486425010.webp)
10
105647
UNVENTED NATURAL GAS FIREPLACE INSERT
DESA INTERNATIONAL
For more information, visit www.desatech.com
CSA Design-
Certified Equipment
Shutoff Valve With
1/8" NPT Tap*
3" Minimum
From Gas
Meter (5"
W.C. to
10.5" W.C.
Pressure)
Supplied
Flexible Gas
Line
Cap Pipe Tee
Nipple Joint
Sediment Trap
Figure 17 - Gas Connection
* Purchase the optional CSA design-certi-
fied equipment shutoff valve from your
dealer. See Accessories, page 26.
INSTALLING GAS PIPING TO
FIREPLACE LOCATION
Installation Items Needed
Before installing fireplace insert, make sure
you have the items listed below.
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connec-
tor (if allowed by local codes) (not provided)
* A CSA design-certified equipment shutoff
valve with 1/8" NPT tap is an acceptable
alternative to test gauge connection. Pur-
chase the optional CSA design-certified
equipment shutoff valve from your dealer.
See Accessories, page 26.
WARNING: A qualified ser-
vice person must connect fire-
place Insert to gas supply. Fol-
low all local codes.
WARNING: Never connect
fireplace insert to private (non-
utility) gas wells. This gas is com-
monly known as wellhead gas.
CAUTION: Use only new,
black iron or steel pipe. Inter-
nally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of 1/2"
diameter or greater to allow
proper gas volume to fireplace
insert. If pipe is too small, undue
loss of pressure will occur.
CAUTION: Use pipe joint seal-
ant that is resistant to liquid pe-
troleum (LP) gas.
We recommend that you install a sediment
trap in supply line as shown in Figure 17.
Locate sediment trap where it is within
reach for cleaning. Install in piping system
between fuel supply and heater. Locate sedi-
ment trap where trapped matter is not likely
to freeze. A sediment trap traps moisture
and contaminants. This keeps them from
going into fireplace insert gas controls. If
sediment trap is not installed or is installed
wrong, fireplace may not run properly.
Installation must include an equipment
shutoff valve, and plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from
fireplace insert (see Figure 17).
IMPORTANT:
Install equipment shutoff
valve in an accessible location. The equip-
ment shutoff valve is for turning on or
shutting off the gas to the appliance.
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• Phillips screwdriver
• sealant (resistant to propane/LP gas, not
provided)
1.
Remove fireplace insert screen. Re-
move two screws that hold fireplace
insert screen in place for shipping.
These screws are located near top of
screen. Discard screws. Lift fireplace
insert screen up and pull out to remove.
CONNECTING FIREPLACE
INSERT TO GAS SUPPLY
INSTALLATION
Continued
NOTICE: If your installation does
not meet the minimum clearances
shown, you must do one of the
following:
• raise the mantel to an accept-
able height
• remove the mantel
Mantel Clearances for Insert
Installation
If there is a mantel above masonry fireplace,
you must meet minimum clearance between
mantel shelf and top of fireplace opening.
NOTICE: Surface temperatures of
adjacent walls and mantels be-
come hot during operation. Walls
and mantels above the firebox
may become hot to the touch. If
installed properly, these tempera-
tures meet the requirements of
the national product standard.
Follow all minimum clearances
shown in this manual.
7.
Attach fireplace to wall studs using
nails or wood screws through holes in
nailing flange (see Figure 16).
8.
Check all gas connections for leaks. See
Checking Gas Connections, pages 11
and 12.
9.
Install surround kit. See Installing
Surround Kit (GS38 or GS43), pages
7 and 8.
Figure 16 - Attaching Fireplace Insert to
Wall Studs
Nails or
Wood
Screws
Nailing
Flanges
Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged fireplace valves.