background image

www.desatech.com

110882-01K

5

Figure 1 - Product Identification

Front 
Log 

Rear Log

Middle 
Log

Base Assembly

Control Knob

Front 
Burner

Piezo 
Ignitor

Front 
Log

Control 
Knob

Rear Log

Base 
Assembly

Front 
Burner

Piezo 
Ignitor

Rear Burner

Middle 
Log

Selector Switch 
(Optional) 

Flame 
Adjustment 
Knob

Remote 
Control 
(Optional) 

Rear Burner

PRODUCT 

IDENTIFICATION

UNPACkING

 CAUTION: Do not remove the 

data  plates  from  the  grate  as-

sembly. The data plates contain 

important  warranty  and  safety 

information.

1.  Remove logs and heater base assembly from 

carton. 

Note:

 Do not pick up heater base as

-

sembly by burners. This could damage heater. 

Always handle base assembly by grate. 

2.  Remove all protective packaging applied to 

logs and heater for shipment.

3.  Check all items for any shipping damage. If 

damaged, promptly inform dealer where you 

bought heater.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no outside 

venting. There is no heat loss out a vent or up a 

chimney. Heat is generated by both realistic flames 

and glowing coals. This heater is designed for vent-

free operation with flue damper closed. It has been 

tested and approved to ANSI Z21.11.2 standard for 

unvented heaters. State and local codes in some 

areas prohibit the use of vent-free heaters. This 

heater may also be operated as a vented decorative 

(ANSI Z21.60) product by opening the flue damper 

(Non-Thermostat Models Only).

SAFETY DEvICE

This heater has a pilot with an Oxygen Depletion 

Sensing (ODS) safety shutoff system. The ODS/pilot 

is a required feature for vent-free room heaters. The 

ODS/pilot shuts off the heater if there is not enough 

fresh air.

PIEZO IGNITION SYSTEM

This heater has a piezo ignitor. This system re

-

quires no matches, batteries or other sources to 

light heater.

OPTIONAL REMOTE 

CONTROL ACCESSORIES

There  are  four  optional  remote  controls  that 

can be purchased separately for Remote-Ready 

Models Only:

•  wall switch

•  wall thermostat

•  hand-held ON/OFF remote

•  hand-held thermostat remote.

See 

Accessories

, page 42.

The  wall  thermostat  or  hand-held  thermostat 

may not be used where vented decorative list

-

ing is required.

Summary of Contents for R 18" Remote-ready













































Reviews: