background image

www.desatech.com

110882-01K

12

Area of various Standard

Round Flues

 

Diameter 

Area

 

5" 

20 sq. inches

 

6" 

29 sq. inches

 

7" 

39 sq. inches

 

8" 

51 sq. inches

  Chimney 

Minimum Permanent 

 

Height 

Flue Opening

 

6' to 15' 

39 sq. inches

  15' to 30' 

29 sq. inches

If reasons number 1 or 2 apply to you, you must 

permanently open chimney flue damper. You must 

install the damper clamp accessory (to order, see 

Accessories

, page 42). This will insure vented 

operation (see Figure 10). The damper clamp will 

keep damper open. Installation instructions are 

included with clamp accessory. 

See chart below for minimum permanent flue 

opening you must provide. Attach damper clamp 

so the minimum permanent flue opening will be 

maintained at all times. 

INSTALLATION

Continued

Figure 10 - Attaching Damper Clamp

Damper 
Clamp

Damper

Manufactured 

Fireplace

Masonry Fireplace

Damper

Damper

INSTALLING HEATER BASE 
ASSEMBLY

 WARNING: You must secure 

this heater to fireplace floor. If 

not, heater will move when you 

adjust controls. Moving heater 

may cause a gas leak.

 WARNING: If installing in a 

sunken  fireplace,  special  care 

is  needed.  You  must  raise  the 

fireplace  floor  to  allow  access 

to  heater  control  panel.  This 

will  insure  adequate  air  flow 

and guard against sooting and 

controls being damaged. Raise 

fireplace floor with noncombus-

tible material. Make sure material 

is secure.

  CAUTION:  Do  not  pick  up 

heater base assembly by burn-

ers. This could damage heater. 

Only handle base assembly by 

grates.

IMPORTANT:

 Make sure the heater burners are 

level. If heater is not level, heater will not work 

properly. For thermostat models, avoid damage 

to thermostat bulb. Avoid nicks or sharp bends 

in thermostat bulb wire. Keep thermostat bulb 

in mounting bracket until ready to mount base 

to floor. See 

Optional Positioning Of Thermostat 

Sensing Bulb

, page 33.

Installation Items Needed

•  hardware package (provided with heater)

•  approved flexible gas hose and fittings (not 

provided) (if allowed by local codes) 

•  sealant (resistant to propane/LP gas, not pro

-

vided)

•  electric drill with 3/16" masonry drill bit

Note:

  Install  optional  HRC200  Receiver  and 

Hand-Held Remote Control Kit (see 

Accessories,

 

page 42) before installing gas log heater (Remote-

Ready Models Only). See installation instructions 

included with the kit. 

Summary of Contents for R 18" Remote-ready













































Reviews: