background image

www.desatech.com

110399-01J

27

CLEANING AND MAINTENANCE

particles of dust, dirt, lint, or pet hair with 
a soft cloth or vacuum cleaner nozzle.

5.  Blow air into the primary air holes on the 

injector holder.

6.  In case any large clumps of dust have now 

been pushed into the burner repeat steps 
3 and 4.

Clean the pilot assembly also. A yellow tip on 
pilot flame indicates dust and dirt in the pilot 

assembly. There is a small pilot air inlet hole 

about  2"  from  where  the  pilot  flame  comes 

out  of  the  pilot  assembly  (see  Figure  41). 

With unit off, lightly blow air through air inlet 
hole. You may blow through a drinking straw 

if compressed air is not available.

LOGS

•  If you remove logs for cleaning, refer to 

Install-

ing Logs

, page 17, to properly replace logs.

•  Replace log(s) if broken or chipped (dime-

sized or larger).

Burner 
Tube

Pilot Assembly

Pilot Air 
Inlet Hole

Ports/Slots

Burner 
Tube

Injector Holder 
(May Be Brass 

or Aluminum 

Depending on 

Model)

Primary Air Inlet Holes 
(Shape of Holes May 
Vary by Model)

Figure 40 - Injector Holder On Outlet 

Burner Tube

Figure 41 - Pilot Inlet Air Hole

  WARNING:  Turn  off  heater 

and let cool before cleaning.

  CAUTION:  You  must  keep 

control  areas,  burners,  and 

circulating  air  passageways 

of  heater  clean.  Inspect  these 

areas of heater before each use. 

Have  heater  inspected  yearly 

by  a  qualified  service  person. 

Heater may need more frequent 

cleaning  due  to  excessive  lint 

from carpeting, pet hair, bedding 

material, etc.

  WARNING:  Failure  to  keep 

the  primary  air  opening(s)  of 

the burner(s) clean may result in 

sooting and property damage.

CLEANING BURNER INjECTOR 
HOLDER AND PILOT AIR INLET HOLE

The  primary  air  inlet  holes  allow  the  proper 
amount of air to mix with the gas. This provides 
a clean burning flame. Keep these holes clear 
of dust, dirt, lint, and pet hair. Clean these air in

-

let holes prior to each heating season. Blocked 

air holes will create soot. We recommend that 

you clean the unit every three months during 
operation and have heater inspected yearly by 

a qualified service person.

We also recommend that you keep the burner 
tube and pilot assembly clean and free of dust 

and dirt. To clean these parts we recommend 

using compressed air no greater than 30 PSI. 

Your local computer store, hardware store, or 

home center may carry compressed air in a 

can. If using compressed air in a can, please 
follow the directions on the can. If you don't 
follow directions on the can, you could dam

-

age the pilot assembly.

1.  Shut off unit, including pilot. Allow unit to 

cool for at least thirty minutes.

2.  Inspect burner, pilot, and primary air inlet 

holes on injector holder for dust and dirt 
(see Figures 40 and 41).

3.  Blow air through the ports/slots and holes 

in the burner.

4.  Check injector holder located at the end of 

the burner tube again. Remove any large 

Summary of Contents for FLAME-MAX H18N









































Reviews: